TRUE FINE Sunrise 4-Light Chandelier Instruction Manual
- October 30, 2023
- TRUE FINE
Table of Contents
TRUE FINE Sunrise 4-Light Chandelier
Product Information
The 4-Light Chandelier is a lighting fixture that comes with a fixture body (A), PC board (B), shade (C), screw (D), stem (E), canopy (G), mounting strap (J), screw (H), screw (I), finial (F), and bulbs (K) which are not included. The input voltage of the chandelier is 120V and the rated power is 60W MAX. The lamp socket used in this product is E26.
Product Usage Instructions
- Pass the wire through Shade (C) and fix Shade (C) to Fixture body (A) with Screw (D).
- Screw PC board (B) to the bottom nut of Fixture body (A).
- Pass the wire through Stem (E) and Canopy (G), then assemble Stem (E) and Canopy (G) to Fixture body (A).
- Fix Mounting strap (J) to the outlet box with Screw (H).
- Connect the wires according to the wiring instruction provided. Never connect the ground wire to black or white power supply wires.
- Pass Canopy (G) through the Screw (I) and fix it with Finial (F).
- Install Bulbs (K) to the socket.
Wiring Instructions
- Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
- Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions provided.
- [GROUP A]: Connect to Black House Wire
- [GROUP B]: Connect to White House Wire
- Take your fixture wire(s) from [Group A] and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
- Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
- Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
- Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Cleaning
To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.
Contact Us
If you have any questions or concerns regarding this product, please email us at service@24h-reply.com.
Overview
Assembly Instruction
- Pass the wire through Shade (C) and fix Shade (C) to the Fixture body (A) with Screw (D).
- Screw PC board (B) to the bottom nut of Fixture body (A).
- Pass the wire through Stem (E) and Canopy (G), then assemble Stem (E) and Canopy (G) to Fixture body (A).
- Fix the Mounting strap (J) to the outlet box with Screw (H).
- Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
- Pass Canopy (G) through the Screw (I) and fix it with Finial (F).
- Install Bulbs (K) (not included) to the socket.
Wiring Instruction
-
Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. -
Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
[GROUP A]:
Connect to Black House Wire
| [GROUP B]:
Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT A TRACER| BROWN, GOLD OR BLACK WITH A TRACER
3. Take your fixture wire(s) from [Group A] and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Product Specifications
- Input voltage 120V
- Rated power 60W MAX
- Lamp socket E26
Product Packaging
- Fixture body × 1
- Shade × 1
- Screw × 2 & Stem × 4
- PC board × 1
- Mounting strap × 1 & Canopy × 1
- Screw × 2 & Wire nut × 3
- Lamp instruction × 1
Cleaning
To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.
CONTACT US
E-mail:service@24h-reply.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>