StarTech com 102B-USBC-MULTIPORT USB-C DP 1.4 Multiport Adapter User Guide
- June 4, 2024
- StarTech com
Table of Contents
StarTech com 102B-USBC-MULTIPORT USB-C DP 1.4 Multiport Adapter
Product ID
102B-USBC-MULTIPORT
Product Diagram
(Side A)
Function
| Component | Function |
|---|
1
|
Built-in USB-C Host Cable
| • Connect to a USB-C Port on a Host Laptop
• USB 3.2 Gen 2 (10Gbps)
• Power Delivery 3.0 Specification
2
|
USB-C Data Port
|
• Connect a USB-C peripheral
• USB 3.2 Gen 2 (10Gbps)
3
|
USB-A Data/Charge Port
| • Connect and/or charge a USB-A peripheral
• USB 3.2 Gen 2 (10Gbps)
• Supports BC1.2 5V/1.5A (7.5W)
• USB-C Power Adapter required for charging
---|---|---
4
|
SD Card Reader
| • Secure Digital (SD) 4.0 UHS-II, SD 3.0, 2.0, 1.1, and 1.0 compatibility
• Push an SD Card, label side up, into the SD
• Card Slot
• Note: The Host Computer’s Operating System (OS) will automatically detect the SD Card and install the required driver software
• Pull the SD Card to remove
5
|
2 x HDMI Output Ports
| • Connect to HDMI Display Devices
• HDMI 2.0
• Up to 4K (4096×2160) 60Hz
6
|
Gb Ethernet Port
| • Connect a CAT 5e/CAT 6 cable to establish a network connection
• 10/100/1000Mbps
7
| USB-C 100W Power
Delivery Port
| • Connect a USB-C power adapter
• USB Power Delivery 3.0 (up to 100W, with up to 85W available for charging)
Requirements
For the latest requirements, please visit www.StarTech.com/102B-USBC-
MULTIPORT.
Installation
Side A Ports
-
If you have a Windows computer with Internet access, connect the Built-in USB-C Host Cable on the Multiport Adapter to a USB-C port on your host laptop. Your computer will automatically detect the device and install all the required drivers. If you’re running a non-Windows operating system or the drivers do not automatically install, disconnect the device from your computer, then:
- Navigate to www.StarTech.com/102B-USBC-MULTIPORT and click the Drivers/Downloads tab.
- Under Driver(s), download the Driver Package for your operating system, and follow the steps outlined in the Installation guide, that’s included in the Driver Package.
-
When connecting USB peripheral devices, connect a USB-C cable from your USB peripheral device to the USB-C Data Port on the Multiport Adapter.
Note: The USB port will output whatever bus power is available, up to 4.5W. -
Connect a USB-A cable from your USB peripheral device to the USB-A Data/Charge Port on the Multiport Adapter, to connect the device to your computer, and/or charge your device with up to 5V/1.5A (7.5W).
Notes:- A USB-C power adapter must be connected to the USB-C DATA/ 100W Power Delivery Port on the Multiport adapter, in order to charge connected peripheral devices.
- Without a power adapter connected, the USB port will output whatever bus power is available, up to 4.5W.
-
Insert your memory card into the SD Card Reader, and press the card to lock it into place. Your computer will recognize the card and mount it as a drive on your connected host computer. To remove the memory card, push the card in and then pull the memory card out.
Note: To protect your memory card and the data stored on it, it’s important to safely unmount (eject) the card within your computer’s operating system, before physically removing the card from the Multiport Adapter.
Side B Ports
- Connect an HDMI cable from up to two HDMI-enabled display devices to the HDMI Output Ports on the Multiport Adapter, to add additional HDMI displays to your workstation.
- Connect a CAT 5e/CAT 6 cable from your local area network (e.g. Router, Switch, Modem, etc.) to the Gb Ethernet Port on the Multiport Adapter, to access your network via a wired LAN connection.
Side C Ports
- Connect a USB-C power adapter (up to 100W) from an AC outlet to the USB-C 100W Power Delivery Port on the Multiport Adapter, to charge the laptop that’s connected to Built-in USB-C Host Cable.
Note:
The Multiport Adapter reserves 15W of power, with up to 85W available for
charging your laptop.
Regulatory Compliance
FCC – Part 15
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a 3-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP
(or their officers, directors, employees or agents) for any damages (whether
direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of profits, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceed the actual price paid for
the product. Some states do not allow the exclusion or limitation of
incidental or consequential damages. If such laws apply, the limitations or
exclusions contained in this statement may not apply to you.
StarTech.com Ltd.
45 Artisans Cres London, Ontario N5V 5E9 Canada
StarTech.com LLP
4490 South Hamilton Road Groveport, Ohio 43125 U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15 Gowerton Rd, Brackmills Northampton NN4 7BW United Kingdom
StarTech.com Ltd.
Siriusdreef 17-27 2132 WT Hoofddorp The Netherlands
- FR: startech.com/fr
- DE: startech.com/de
- ES: startech.com/es
- NL: startech.com/nl
- IT: startech.com/it
- JP: startech.com/jp.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>