TRUE FINE TD10052FL Flush Mount Lighting Instruction Manual
- October 30, 2023
- TRUE FINE
Table of Contents
TRUE FINE TD10052FL Flush Mount Lighting
Product Information
The Flush Mount Lighting is a lighting fixture that can be mounted directly onto an outlet box. The product comes with a fixture body (A), crystal (B), canopy (D), finial (C), mounting strap (E), wire nuts, screws (F), and spare bulbs. The product has two wire groups: Group A, which includes a black wire and a parallel wire with a smooth surface, and Group B, which includes a white wire and a parallel wire with a ribbed surface. The product also has a green grounding screw and bare copper wire for grounding.
Product Usage Instructions
- Hang the crystal (B) onto the fixture body (A).
- Pass the wires through the canopy (D) and screw the canopy (D) to the fixture body (A).
- Fix the mounting strap (E) to the outlet box using screw (F).
- Connect the wires according to the wiring instructions and pictures provided.
- Pass the canopy (D) through the screw and fix it with the finial (C).
Wiring Instructions
- Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
- Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
- [GROUP A]: Connect to Black House Wire
- [GROUP B]: Connect to White House Wire
- Take your fixture wire(s) from [Group A] and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
- Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
- Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
- Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Product Specifications
- Product Packaging: The product is packed with all the necessary components for installation.
- Cleaning: To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.
Contact Us
E-mail : service@24h-reply.com
Printed in China
Wiring Instruction
-
Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. -
Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
[GROUP A]:
Connect to Black House Wire
| [GROUP B]:
Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Overview
Assembly Instruction
- Hang Crystal (B) onto Fixture body (A).
- Pass the wires through Canopy (D), then screw Canopy (D) to Fixture body (A).
- Fix Mounting strap (E) to outlet box with Screw (F).
- Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
- Pass Canopy (D) through the screw and fix it with Finial (C).
Product Specifications
- Input voltage 120V
- Rated power 60W MAX × 2
- Lamp socket E26
- Product Packaging
- Fixture body × 1
- Crystal × 48
- Mounting strap × 1 & Canopy × 1
- Screw × 2 & Wire nut × 3
- Lamp instruction × 1
Cleaning
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.
CONTACT US
E-mail:service@24h-reply.com