Hukoro F50543-QC 3-Light Bronze Farmhouse Geometric Pendant Light Instruction Manual

Hukoro F50543-QC 3-Light Bronze Farmhouse Geometric Pendant Light

Product Information

The product is a light fixture that requires assembly and installation. It includes various hardware items such as a fixture, nipple and nut, cover, fixture finial, glass shade, stem, holders, chain, canopy, screw collar ring, mounting unit, mounting screws, and wire nuts. The product also comes with an instruction manual that outlines the assembly and installation process.

Product Tools Required

Before starting the assembly process, ensure that the following tools are available:

• Ladder
• Safety glasses
• Electrical Phillips screwdriver
• Flat blade screwdriver
• Pliers
• Wire strippers
• Tape

Note: Removing the fuse at the fuse box is also required for safety purposes.

Product Hardware Included

The following hardware items are included in the package:

• Fixture
• Nipple and Nut
• Cover
• Fixture Finial
• Glass Shade
• Stem
• Holders
• Chain
• Canopy
• Screw Collar Ring
• Mounting Unit
• Mounting Screws
• Wire Nuts

Note: Parts shown may differ slightly per light fixture.

Product Installation Instructions

1. Adjust the arms of the fixture to the proper position.
2. Attach the mounting unit to the junction box using the mounting screws.
3. Attach the canopy, screw collar ring, fixture finial, cover, nipple and nut, and fixture to the mounting unit.
4. Choose the length of the chain needed and attach it to the fixture finial.
5. Pass the chain and branch wires through the screw collar ring and canopy. Attach the end of the chain to the mounting unit and feed the branch wires through the pipe nipple on the mounting unit.
6. Make the electrical connection from the junction box to the fixture. Connect the ground wire to the mounting unit using the preinstalled green ground screw. Then, connect the positive, negative, and ground wires with the supplied wire nuts. Secure with electrical tape.
7. Secure the canopy to the mounting unit with the screw collar ring.
8. Attach the glass shade onto the fixture using holders and stem.
9. Install a bulb (not included).

Note: The black or red wire (hot) from the junction box should be connected to the smooth side of wire from the fixture identified with the label L. The white wire (neutral) from the junction box should be connected to the ribbed side of wire from the fixture identified with the label N. The bare or green ground wire from the junction box should be connected to the ground wire from the fixture using the preinstalled green ground screw. Sealing tape is not included.

CAUTION

• Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation.
• Before starting the installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.

TOOLS REQUIRED

HARDWARE INCLUDED

• PARTS SHOWN MAY DIFFER SLIGHTLY PER LIGHT FIXTURE

EXPLODED PARTS

INSTALLATION

• STEP 1
  • Adjust arms to proper position.
• STEP 2

1. Weave the fixture wire and fixture ground wire through the nipple and nut, cover and fixture finial.
2. Tighten the nipple and nut, cover and fixture finial into the fixture.

• STEP 3
  • Use the mounting screws to attach the mounting unit to the junction box.
• STEP 4

1. Choose the length of the chain you need (Open the chain using a phillips screwdriver (not included) and pliers (not included). )
2. Attach the end of the chain to the fixture finial.

• STEP 5

1. Pass the chain and the branch wires through the screw collar ring and canopy.
2. Attach the end of the chain to the mounting unit.
3. Feed the branch wires through the pipe nipple on the mounting unit.

• STEP 6
  • Make the electrical connection from the junction box to the fixture.
  • Connect the ground wire to the mounting unit using the preinstalled green ground screw.
  • Then, connect the positive, negative and ground wires with the supplied wire nuts. Secure with electrical tape.
• STEP 7
  • Secure the canopy to the mountring unit with the screw collar ring.
• STEP 8
  • Attach the glass shade onto fixture using holders and stem.
• STEP 9
  • Install bulb (not included)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>