ALPHA ESC-150 6 Inch Electric Wet Dry Stone Cutter Instruction Manual

: June 11, 2024
: Alpha

Table of Contents

ALPHA ESC-150 6 Inch Electric Wet Dry Stone Cutter
Product Information
Product Usage Instructions
SPECIFICATIONS
INTRODUCTION
TOOL SET-UP INFORMATION
MAINTENANCE
OPERATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ALPHA ESC-150 6 Inch Electric Wet Dry Stone Cutter

ALPHA-ESC-150-6-Inch-Electric-Wet-Dry-Stone-Cutter-
product

Product Information

The ESC-150/ESC-250 is an electric wet/dry stone cutter with a 1200W motor that operates at a speed of 10,000 RPM. It comes in two variants – 110 Volts and 220 Volts. The tool weighs 11.30 lbs (A-110V) or 5.12 kgs (C-230V) and has a blade diameter of 6 inches (150mm) for ESC-150 and 2 7/8 inches for ESC-250. The blade arbor size is 50.80mm for ESC-150 and 22.23mm for ESC-250.

Product Usage Instructions

Before using the electric wet/dry stone cutter, carefully read the owner’s manual to understand its applications, limitations, and potential hazards. Always follow the safety instructions for power tools provided in the manual.

Safety Instructions:

Keep your work area clean to avoid accidents.
Avoid using the tool in the presence of flammable liquids or gases and keep the area dry and well-lit.
Keep children and visitors away from the work area and out of reach of the tool.
Do not force the tool beyond its designed capacity.
Wear proper apparel, including rubber gloves and insulated non-skid footwear, and a protective covering to contain long hair. Do not wear loose clothing or jewelry that can get caught in moving parts.
Always wear proper personal eye protection that conforms with ANSI/ISEA Z87.1 (CAN/CSA Z94.3). Use a face or dust mask if the operation is dusty. Always wear certified safety equipment.
All users and bystanders must wear proper personal ear protection which conforms with ANSI S12.6 (S3.19) hearing protection.
All users and bystanders must wear proper personal respiratory protection. Always use NIOSH/OSHA-approved respiratory protection appropriate for dust exposure.

When using the electric wet/dry stone cutter, ensure that the blade is securely mounted and the tool is properly grounded. Always use the appropriate blade for the material being cut. Do not use the tool for any purpose other than its intended use. Make sure to observe all safety instructions and notes provided in the manual to ensure the safe and correct use of the electric wet/dry stone cutter.

SPECIFICATIONS

ALPHA-ESC-150-6-Inch-Electric-Wet-Dry-Stone-Cutter-
fig-2

INTRODUCTION

Thank you for purchasing the Alpha® ESC-150/ESC‑250 6” Electric Wet/Dry Stone Cutter. Please read this instruction manual thoroughly to ensure the safe and correct use of the electric wet/dry stone cutter. Keep this manual in a place where operators can access it easily whenever necessary.

ABOUT THE SYMBOLS: According to the hazard level, all safety notes in this manual are classified into “DANGER”, “WARNING” and “CAUTION”.
DANGER: Death or serious personal injury is imminent when handling this electric wet/dry stone cutter incorrectly.
WARNING: There is a possibility of death or serious personal injury when handling this electric wet/dry stone cutter incorrectly.
CAUTION: There is a possibility of personal injury or property damage when handling this electric wet/dry stone cutter incorrectly.
NOTE: In some situations, failure to observe
WARNING: notes could result in death or serious personal injury. Be sure to read and observe the safety notes to ensure the safety and correct use of the electric wet/dry stone cutter.

SAFETY INSTRUCTIONS FOR POWER TOOLS

Know Your Power Tool. Read owner’s manual carefully. Learn its applications and limitations as well as specific potential hazards particular to this tool.
Keep Work Area Clean. Cluttered areas and benches invite accidents.
Avoid Dangerous Environments. Keep work areas as dry as possible. Do not use tool in the presence of flammable liquids or gases. Keep the area well-lit.
Keep Children and Visitors Away. All visitors should be kept a safe distance from the work area. Keep out of reach of children.
Don’t Force Tool. It will do the job better and safer at the rate for which it was designed.
Wear Proper Apparel. Do not wear loose clothing or jewelry as it can get caught in moving parts. Rubber gloves and insulated non-skid footwear are recommended. Wear a protective covering to contain long hair.
Wear Proper Eye Protection. All users and bystanders must always wear proper personal eye protection which conforms with ANSI/ISEA Z87.1 (CAN/CSA Z94.3). Also, use a face or dust mask if the operation is dusty. Always wear certified safety equipment.
Wear Proper Ear Protection. All users and bystanders must wear proper personal ear protection which conforms with ANSI S12.6 (S3.19) hearing protection.
Wear Proper Respiratory Protection. All users and bystanders must wear proper personal respiratory protection. Always use NIOSH/OSHA approved respiratory protection appropriate for dust exposure.
WARNING! Some dust created by power sanding, sawing, grinding, drilling, polishing, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:
- Lead from lead-based paints
- Crystalline silica from bricks, cement, and other masonry products, and
- Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. To familiarize yourself with the risks associated with a material, consult with your employer, manufacturer/ supplier, and government agencies regarding the hazards of the materials and their recommendations to protect yourself.
Don’t Abuse Water Supply Hose. Don’t carry tool by supply hose or expose to traffic areas where it can be crushed.
Always Secure Work Piece. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool.
Don’t Overreach. Keep proper footing and balance at all times.
Disconnect Tools When Not In Use. Always disconnect tool before servicing and when changing accessories.
Remove Adjusting Keys And Wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
Maintain Tools With Care. Keep tools clean at all times for best and safest performance. Follow instructions for lubricating and changing accessories. Keep handles dry, clean and free of oil or grease. Inspect moving parts for alignment and binding as well as for breakage and improper mounting.
Avoid Accidental Starting. Do not carry a “connected” tool, or make adjustments, or change discs without making sure the tool is disconnected from the air supply.
Use Only Recommended Accessories. The use of any accessories other than what is listed or recommended for this particular tool may be hazardous.
Keep Hands Away From All Moving Parts.
Use Side Handles. Supplied with tool for
control and safety.
Stay Alert. Watch what you are doing and use common sense. Do not operate tool when you are tired, or under the influence of drugs, alcohol or medication.

ADDITIONAL PRECAUTIONS FOR USING THE ELECTRIC WET/DRY STONE CUTTER
In addition to the general safety notes described on the preceding pages, please read and observe the following precautionary notes before using the electric wet/dry stone cutter.

Keep the water line clear from the working range of the machine. This line should always lead away from you and behind the operating area.
Before use, check the machine, hose, and fittings for any damage or material fatigue. Only authorized service agents should carry out repairs.
Only use saw blades whose permitted speed is at least as high as the highest no-load speed of the machine.
Be sure the saw blade fits the tool properly and securely. Do not modify the tool to force fit the blade. For example, do not remove the blade guard.
Check blades before use. The saw blade must be properly mounted and turn freely. Perform a test run for at least 30 seconds without any load. Do not use damaged, round or vibrating blades.
Immediately switch off the machine in case of considerable vibrations or if other malfunctions occur.
Always use and store the saw blades according to the manufacturer’s instructions.
The flange bolt must be tightened before starting to work with the machine.
The workpiece must be secured if it is not heavy enough to prevent movement.
The tool is designed for cutting on horizontal surfaces.

CE Declaration of conformity

We declare under our sole responsibility according to EMC 2004/108/EC, the
Low Voltage Directive 2006/95/EC and
Machinery Directive 2006/42/EC, that this product is in conformity with the following standards or standardization documents.
Product: Electric Stone Cutter
Model: ESC-150/ESC-250
Applied harmonized standards
EN61000-3-3/+A2:2005,EN55014-
1:2006,EN55014-2/A1:2001,EN61003-3-
11:2006,EN60745-1:2009.
Alpha Professional Tools®
16 Park Drive,
Franklin, NJ 07416