ALPHA CORE RTX-N 3090 Eisblock Aurora TI FTW3 ultra INCL. BACKPLATE Instruction Manual
- October 27, 2023
- ALPHA CORE
Table of Contents
RTX-N 3090 Eisblock Aurora TI FTW3 ultra INCL. BACKPLATE
Instruction Manual
Read the safety instructions before starting the installation.
https://www.alphacool.com/download/SAFETY%20INSTRUCTIONS.pdf
Accessories
Compatability check
Before starting the cooler assembly, compare your card with the pictures in
our configurator. To do so, visit https://www.hwconfig.com and search for
your graphics card or cooler model. For a definitive identification, you can
also compare the PCB number. The cooler was designed for a special PCB layout.
Occasionally, graphics card manufacturers may revise the design of their card
slightly, causing the cooler not to fit on later models. During assembly,
please make sure taller parts have enough space around them and that the
cooler does not damage your graphics card.
Alpha cool International GmbH is not liable for assembly errors occurring due
to negligence, such as selecting an incompatible cooler.
Prepare graphics card
Put the hardware on an antistatic mat. Begin dismantling the original cooler.
Depending on the structure of the cooler, remove the screws at the back of the
card and carefully unhook the fan connector first. If the original cooler uses
thermal glue, extreme care should be taken as you can easily damage parts.
Pick up all the items carefully. Next, clean the hardware of thermal paste or
pad residues with a solvent (e.g. isopropanol alcohol).
Mounting the IO shield
Attach the slot cover as shown using the 2 M3x5 screws and M3 nuts.
Mounting the front pads
Clean the contact surfaces on the bottom side of the cooler with alcohol or
similar. The surface must be free of contaminants.
Remove the protective foils from the thermal pads and place the pads on the
copper block as shown.
Applying thermal paste
With the help of a plastic strip or similar spread a thin layer of thermal
paste on the GPU. The layer should be less than a millimeter thick, otherwise
the surrounding components may be contaminated.
Mounting the graphics card
Place the graphics card on the prepared cooler. Fasten the card as shown with
the 8 M2x5 screws with M2 washers. Hand-tighten the screws crosswise, one turn
at a time.
Mounting the backpads
Remove the protective foils from the thermal pads and place the pads on the
PCB as shown.
Mounting the backplate
Put the backplate on and screw it together with the 8 M2x11 screws as shown.
Connecting the LED
To control the digital – RGB lighting, connect the included adapter to the 3 –
pin female connector and plug it to a digital – RGB controller (e.g.
Alpha cool Aurora Eiscontrol, Art.: 15360, not included). You can connect
additional digital RGB LEDs to the remaining 3 – pin male connector.
Close the inlets which you do not need for tubing. Screw in the screw plugs with the enclosed tool.
Alpha cool International GmbH
Marienberger Str. 1
D-38122 Braunschweig
Germany
Support: +49 (0) 531 28874 – 0
Fax: +49 (0) 531 28874 – 22
E-mail: info@alphacool.com
https://www.alphacool.com
V.1.00-05.2022
Documents / Resources
|
ALPHA CORE RTX-N 3090 Eisblock Aurora TI FTW3 ultra INCL.
BACKPLATE
[pdf] Instruction Manual
RTX-N 3090, Eisblock Aurora TI FTW3 ultra INCL. BACKPLATE, RTX-N 3090 Eisblock
Aurora TI FTW3 ultra INCL. BACKPLATE, Aurora TI FTW3 ultra INCL. BACKPLATE, TI
FTW3 ultra INCL. BACKPLATE, ultra INCL. BACKPLATE, BACKPLATE
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>