JAXPETY HG61T1296 8′ x 12′ Outdoor Metal Storage Shed with Sliding Doors for Backyard Instruction Manual

JAXPETY HG61T1296 8′ x 12′ Outdoor Metal Storage Shed with Sliding Doors

for Backyard

Product Information

This product is designed for drilling purposes and includes  various parts, including screws F1 and F4. It is important to note that the 2 screws fixed in this step will need to be removed and reinstalled later in the following steps. Additionally, it should be mentioned that part 7 and part 8 do not have pre-drilled holes, but they can be easily fixed with screws F1 or F4.

Product Usage Instructions

1. Identify the 2 screws that are currently fixed in place.
2. Carefully remove the 2 screws from their current position.
3. Proceed with the subsequent steps as outlined in the user manual.
4. Locate part 7 and part 8, which do not have pre-drilled holes.
5. Select either screw F1 or F4 to fix part 7 and part 8 securely.
6. Align part 7 and part 8 with the desired placement.
7. Using the selected screw (F1 or F4), carefully drill through part 7 and part 8, securing them in place.
8. Continue following the remaining instructions provided in the user manual for further usage guidance.

Assembly Preparation

Owner’s Manual
Please check local building codes regarding footings, location and other requirements before beginning construction.

Assembly instructions
Reviewing all instructions and the appropriate information before you begin, make sure following the step sequence carefully for successful results.

Flooring base
A good location for the storage building is a square and level area with good drainage. The base is not included in the kit which may need purchase separately or may construct a foundation and anchoring system of your own.
A strong plastic sheet (thickness: at least 150µm) should be placed under the foundation to assist in reducing rising dampness from the soil, thus reducing condensation build up in the shed. Your storage building must be anchored to prevent wind damage. Once secured, it is highly recommended applying silicone along the inside of the base rail to minimize condensation.

Parts and Parts List
Before you start, separate and identify all the parts and hardware to be sure that you have all the necessary parts for your building (refer to the Parts List Page).
If you find that a part is missing, please notify the seller within one week after receiving the product. Do not attempt to assemble the building if parts are missing because any building left partially assembled may be seriously damaged by light winds.

Tools you need
( Please tear off the safety protection layer before the assembly, keep the part number label if needed )

Safety must be put in the No. 1 position

1. Select a dry and calm day for your assembly. Team works (Two or more people) are required during the assembly. It is also recommended to finish the assembly in a day to avoid damage to the product or missing of some small parts.
2. Wearing safety gloves, eye protection and long sleeves during the assembly to prevent injury. Pay attention to the sharp edge of some parts.
3. Children and pets are not allowed entering into the construction site.
4. Never concentrate your total weight on the roof of the building.
   When using a step ladder make sure that it is safe.

Care & Maintenance

1. Keep the shed clean with soft cloth, use water if necessary.
2. Keep the door tracks clear of dirt and other stuff that prevent them from sliding easily.
3. Clean the snow with necessary tools to make sure it is safe to enter into.
4. The shed is not made for living but storing stuff.
5. Please add some oil on the top and bottom door sliding channel to make door slides smoothly.

Size

Area of installation requirement TOP2 TOP1

Hardware List

PRODUCT ASSEMBLY

Check the package contents before getting started !

STEP 1

STEP 2

STEP 3 STEP4

STEP 5

• The floor frame must be level and square or holes will not align.
• (Notice: Measure the floor frame diagonally. When the diagonal measurements are equal, the floor frame is square.)

& Make the colored side of the steel plate outward.

STEP6

STEP 7

STEPS 8

STEP9

STEP 10

STEP 11

STEP 12 STEP 13

STEP 14

Put the side with fewer holes facing up.

STEP 15 Put the side with fewer holes facing up.

STEP 16 Put the side with fewer holes facing up.

STEP 17 Put the side with fewer holes facing up.

STEP 18 ? Put the side with fewer holes facing up.

STEP 19 Put the side with fewer holes facing up.

STEP 20

Put the side with fewer holes facing up.

STEP 21 & Put the side with fewer holes facing up.

STEP 22 & Put the side with fewer holes facing up.

STEP 23 Put the side with fewer holes facing up.

STEP 24

STEP 25

• The 2 screws fixed in this step need to be removed and reinstalled later in the following steps.
• There are not pre-drilled holes on part 7 and part 8, but they can be easily fixed with screws F1 or F4.

STEP26

STEP 27

STEP 28

STEP 29

STEP 30

STEP 31

STEP 32

STEP 33

STEP 34

STEP 35

STEP 36

STEP 37

STEP 38

STEP 39 Remove the 2 screws installed in Step 25 and then do this step.

STEP 40 The side with holes should be face-up.

STEP 41

STEP 42

The side with holes should be face-up.

Please install by the number order shown in the
Step 42, or the holes in the roof panel cannot be aligned.

STEP 43 Screws on the top panel can’t be fixed too tightly • [D in the beginning, and they can only be tightened

STEP 44

STEP 45

STEP 46

STEP 47

STEP 48

STEP 49

STEP 50

STEP 51

STEP 52

STEP 53

STEP 54

STEP 55

STEP 56

STEP 57

STEP 58

STEP 59

STEP 60

STEP 61

STEP 62

STEP 63

Documents / Resources

| JAXPETY HG61T1296 8' x 12' Outdoor Metal Storage Shed with Sliding Doors for Backyard [pdf] Instruction Manual
HG61T1296 8 x 12 Outdoor Metal Storage Shed with Sliding Doors for Backyard, HG61T1296, 8 x 12 Outdoor Metal Storage Shed with Sliding Doors for Backyard, Shed with Sliding Doors for Backyard, Sliding Doors for Backyard, for Backyard
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>