lionelo Babyline 8.2 Baby Video Monitor User Manual

Babyline 8.2 Baby Video Monitor
User Manual

Babyline 8.2 Baby Video Monitor

|
---|---
|
|

Dear Customer!
In case of any questions or comments on the purchased product, please contact us: help@lionelo.com
Producer:
BrandLine Group Sp. z o. o.
ul. A. Kręglewskiego 1, 61-248 Poznań, Poland

Important

1. This product is not a toy. Do not let children play with it.
2. The product is intended for use in dry places only. It is forbidden to use it outdoors or on wet surfaces.
3. Do not touch the device if your hands are wet.
4. Do not use the device if the cable or plug is damaged.
5. If the device acts up or has been dropped or flooded, contact the manufacturer’s service center.
6. To unplug the device, grab the plug, not the cable.
7. If you do not use the device for a long time, unplug it.
8. Please use the power adapter supplied only.
9. It is forbidden to place the product near a cooker or other sources of heat. Battery explosion risk.
10. Only an adult is allowed to assemble the product. Keep small items of the set out of reach of children.
11. The baby monitor cannot substitute for suitable parent’s care and attention.
12. Do not place the baby monitor and its cables in the playpen or within child’s reach. Place them at least 1 m away.
13. Do not place the baby monitor near water or sources of heat.
14. Do not touch plug terminals.

The product complies with requirements of EU directives. Pursuant to the Directive 2012/19/EU, this product is subject to selective collection. The product must not be disposed of together with domestic waste as it may pose a threat to the environment and human health. The worn-out product must be handed over to electrics and electronics recycling point.
Set (fig. A)

1. Camera
2. Display unit
3. Power cable USB x2
4. Adapter x2
5. Operating manual

Description of the device (fig. B, C)

1. Light-sensitive detector
2. Lens
3. Camera microphone
4. Camera LED light
5. Camera power port
6. Temperature sensor
7. SET key
8. Aerial
9. ON/OFF/ECO mode
10. Menu/return key
11. Up/down keys
12. Left/right keys
13. Play music key
14. Display charging port
15. Intercom (long press)/change settings (short press)
16. Charging/sounds volume indicator
17. Display microphone
18. Reset key

Explanation of icons on the screen

| No connection between the camera and display unit
---|---
| Signal strength
| Room temperature
| Battery status
| Temperature alarm active
| Baby feeding reminder active
| Sound alarm active
| Camera not paired/camera unplugged
| Temperature alarm
| Baby feeding reminder
| Low battery
| Sound volume – five LEDs flash in green
Charging – the first LED on the right glows in red

How to use

Put the camera in a desired place (e.g. on the table or shelf) and point the lens at the area you want to monitor (fig. 1).
NOTE! Do not place the camera within child’s reach.
In case of any sound or image interference, reposition the camera and make sure there are no other electric devices nearby.

How to switch the camera on

1. Connect the USB power cable to the camera (fig. 2) and adapter (fig. 3), and then plug the camera in.
2. The camera will activate automatically after you have supplied it with power. The camera LED light will turn green.

How to charge the display unit

1. If it is necessary to charge the device, connect the USB power cable to the display unit (fig. 4) and adapter, and then connect the display unit to the source of power.
2. Full charging takes about 3,5 hours. The battery level icon on the display will stop flashing.

How to switch the display unit on

1. Switch the display unit on by pressing the on/off key (9, fig. C).
2. The display unit has been paired with the camera in the factory. If there is no image on the display unit despite connecting the camera to the source of power, please retake the pairing procedure as described in the sub chapter – How to add and delete the camera.
3. To gain access to the menu, press the menu key (fig. 5).

How to add and delete the camera

How to add the camera

1. In the menu, select icon and press OK.
2. From the list, select the camera which is to be added and press OK. Next choose camera adding (fig. 6).
3. When you can see a command on the screen (fig. 7), press SET on the camera (7, fig. B).
4. When you have successfully paired the camera, the display unit will display image from the camera in real time.
5. While using the device, the camera must be connected to the source of power.

How to delete the camera

1. In the menu, select the icon and press OK.
2. From the list select the camera which is to be deleted and press OK. Next choose camera deleting (fig. 8).

Lullabies

1. In the menu, select icon and press OK.
2. The camera allows you to play five lullabies (fig. 9). Select the lullaby you want to play and press OK. To stop playing, press OK again.
3. Select icon to play all lullabies one after another.
4. In the lullaby selection interface (fig. 9) you can use left/right keys ( ) to change the lullaby, and up/down keys ( ), to change the volume.
5. You can enter the lullaby selection interface also by pressing the music playing key (13, fig. C).

VOX mode

1. VOX mode, a default mode in the device, allows you to save a battery.
2. If the child is sleeping and the device cannot detect any sound in 30 seconds, the display unit will switch into the standby mode, and the image broadcast will be terminated. When the device can detect the sound, the image broadcast will be resumed. No sound alarm.
3. When VOX mode is inactive, the image broadcast can be activated and deactivated manually through a switch. When the image broadcast is inactive, the display unit serves only to transmit sounds. No sound alarm.
4. Cry alert function is available when VOX mode is active (fig. 12).

Cry alert

1. The device can activate the alarm on the display unit and sound signal in case your child starts crying.

2. In the menu, select icon and press OK.

3. Select one of three cry sensitivity levels.
   Low , medium , or high .

4. Select „ON” and next press OK (fig. 10).

5. When the device can detect the child crying, the image broadcast will be resumed and the flashing icon will pop up in the screen, sound alarm will also be activated.

How to set the date and time

1. In the menu, select icon and press OK.
2. Select icon and press OK to set the date and time. Set the date and time and then press OK (fig. 11).
3. OSD (on screen display): decide if the date and time are to be showed on the display screen (ON/OFF, fig. 11).

How to set the language

1. In the menu, select icon and press OK.
2. Select icon and press OK to set the language. Select the language and then press OK.

How to set alarms

1. In the menu, select icon and press OK.
2. Select icon and press OK to set alarms. Activate or deactivate the sound alarm (fig. 12).
3. If the sound alarm is inactive, the temperature/feeding alarm will be displayed only on the screen, with no sound signal.

Temperature alarm

1. The device can sound the alarm on the display unit when the temperature in the child’s room is too low or too high.
2. In alarm settings, select the temperature alarm (fig. 13).
3. Choose the temperature unit (Celsius or Fahrenheit degrees) and press OK.

Baby feeding reminder

1. The device can sound the alarm on the display unit in order to remind you about the scheduled baby feeding.
2. In alarm settings, select the baby feeding reminder (fig. 14).
3. Select alarm/alarms time and press OK.

How to restore the factory settings

1. In the menu, select icon and press OK.
2. Select icon and press OK.
3. The message on the screen will ask you to restore default settings. Choose „YES” and press OK (fig. 15).
4. NOTE! If you restore default settings, you will delete all previous values.

How to reset the device
If the display unit does not work properly, use a needle to press the reset key, located on the left side of the rear cover (18, fig. C). The device will activate again in a moment.
Information on the device

1. In the menu, select icon and press OK.
2. Select icon and press OK to see information on the device (fig. 16).

The pictures are for reference only. The real design of the products may differ from the pictures presented.

Simplified EU declaration of conformity
BrandLine Group Sp. z o. o. hereby declares that the “ BABYLINE 8.2” product complies with the directive: 2014/53/EU – RED Directive,2014/30/EU – EMC Directive, 2014/35/EU – LVD Directive, 2011/65/EU – RoHS Directive.
Full content of EU declaration of conformity is available on the following website: www.lionelo.com/deklaracja_zgodnosci/BABYLINE_82.pdf
Detailed warranty conditions are available on the website: www.lionelo.com
Thank you for purchasing our product

www.lionelo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>