BARRELS No 63 Steam Sauna Bath Installation Guide
- June 9, 2024
- BARRELS
Table of Contents
No 63 Steam Sauna Bath
Barrel Nº63
Installation Guide
No 63 Steam Sauna Bath
Everything you need to build your very own Thermory Barrel Sauna is right
there in front of you. If it looks like a lot, it is. If it seems too
complicated to assemble, it isn’t.
These instructions are specifically written to guide you through each step
with ease. And if you need additional encouragement, you can scan the code on
the back of this guide to see how it’s done.
The Thermory Barrel Sauna Nº63 is designed for up to six people.. That’s
plenty of room for you and the friends helping you put this together. But if
you want to enjoy the first steam all by yourself, we understand.
The Wait Is Over.
We truly appreciate the opportunity to share our love of sauna culture with
you. And if there’s anything we can do to make your sauna experience better,
please don’t hesitate to let us know. If not, just relax and enjoy.
PARTS 1
PARTS 2
STEP
ZERO
Before you begin, be sure the sauna will fit in your chosen location.
Approximately L x W x H of8’ x 8’ x 8’ is ideal. Overall dimensions are shown
here.
Be sure the site is level and free of standing water after rainfall.
Concrete, pavers or crushed stone is preferred. STEP ONE
Measure support cradles (A) diagonally from corner to corner.
Measurements “a” and “b” should be equal to ensure the cradles are square.
Be sure cradles remain level. STEP TWO
Place the support cradles (A) on level site. The middle support cradle will
have no dowel. Carefully level for better stability.
Place the center stave (B) on wooden dowels embedded in outer support cradles
(A).
Fix the center stave (B) with screw 4.2×70 (N). STEP THREE
Place 6 sauna body staves (C) to each side of the center stave (B) and fix
with screws 4.2 x 70 (N).
Body staves (C) are left and right sided.
Be sure to align the panel groove on every next body stave.
STEP FOUR
Place front panel with sauna doors (D) and rear panel (D1) into the trimmed
grooves. Be sure each panel is centered, leveled, and completely seated into
the floor panel.
Bind these panels together by temporarily placing one or two body stave (C) on
top of them.
STEP FIVE
Two front side panels (E, F) attach to the front panel (D) and two back side
panels (E1, F1) attach to the rear panel (D1) by 4 screws 5.0 x 120 (M) and 4
stainless steel screws 4.20 x 70 (N1).
Be sure the bench supports face the interior of the sauna.
Confirm that the combined width of the rear wall (E1, D1, F1) matches the
combined width of the front wall (E, D, F).
STEP
SIX
Continue placing body staves (C) tightly on both sides of the sauna using
rubber mallet, while fixing body staves on the front panel with 4.2 x 70
screws and rear window panel with 4.0 x 50 screws to prevent glass breakage.
To finish the roof top joint, use top stave (H). Different thickness options
are provided to completely fill the gap. 
STEP SEVEN
Measure steel bands (I) to ensure correct length of 276,” +/- 1/2” is
acceptable.
Install steel bands (I) by wrapping bands around barrel prior to connecting
with bolts and nuts (U).
Place steel bands evenly around barrel, covering screw heads.
Measure from steel band to barrel edge to ensure the steel band is even.
Cover roof with roof tape.
Rub and smooth with pressure to ensure adhesion.
Install interior aspen roof trim (O) with 4.0 x 50 (P1) stainless steel
screws.
STEP
EIGHT
Attach bench supporting leg (J1) to the bench (J), install two sauna benches
on wall mounts using stainless steel screws 4.2 x 70 (N1).
Hold the seat and leg assembly tight to the sauna wall. Using a level, make
sure the bench seat is level from front to back. This will ensure proper
placement.
Install backrests (J2) at your chosen height using stainless steel screw 4.0 x
50 (P1).
STEP
NINE
Wire raceways (V) and flooring duckboards (L) can be used for wiring runs,
confirm specific wiring runs needed for chosen stove. STEP TEN
Place waterproof roof cover (Z) and fix it with wooden slat (Z1) and screws
4.0 x 50 (P).
Install front and rear decorative roof finishing boards (W), fixing by screws
4.0 x 50 (P).
WATCH THE VIDEO
https://onedrive.live.com/?authkey=%21AIDnWO5nDgpEHUU&cid=D3989D69E6564C5B&id=D3989D69E6564C5B%21487&parId=D3989D69E6564C5B%21417&o=OneUp
SEE HOW ASSEMBLY
WILL LOOK HERE.
Thermory USA – Denver
537 W. Highlands Ranch Pkwy, Ste. 114
Highlands Ranch, CO 80129
720.759.7268
support@thermoryusa.com| Thermory USA –
Buffalo
56 Harvester Ave, Ste. 1-201
Batavia, NY 14020
585.591.6590
support@thermoryusa.com
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>