lionelo Luna Baby Bed User Manual
- October 30, 2023
- lionelo
Table of Contents
Luna Baby Bed
User Manual
Luna Baby Bed
| 
---|---
| 
| 
| 
Dear Customer!
In case of any questions or comments on the purchased product, please contact
us: help@lionelo.com
Before you use the product, please read this manual carefully.
Producer:
BrandLine Group Sp. z o. o.
ul. A. Kręglewskiego 1, 61-248 Poznań, Poland
NOTE!
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
WARNING
- Do not use this product without reading the instructions for use first.
- Stop using the product as soon as the child can sit or kneel or pull itself up.
- Placing additional items in the product may cause suffocation.
- Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
- Do not use more than one mattress in the product.
- The product should be placed on a horizontal floor.
- Young children should not be allowed to play unsupervised in the vicinity of the crib.
- The crib should be locked in the fixed position when the child is left unattended.
- All assembly fittings must always be properly tightened. Make sure no screws are loose because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc.), which would pose a risk of strangulation.
- The maximum mattress thickness is marked with a line inside the carrycot. Do not use a mattress thicker than permitted.
- Be aware of the threat posed by a burning cigarette, open flame or other sources of high temperature, such as electric heaters, gas water heaters, etc., in the near vicinity of the crib.
- The maximum inclination allowed is a two-level difference. The baby must be placed in the crib with its head at the higher end.
- DO NOT use the crib if any parts are missing, damaged, or broken. Contact Lionelo for replacement parts and instructional literature if needed. DO NOT substitute parts.
WARNINGS FOR MATTRESS:
- Do not use the mattress if any parts are broken, torn or missing. Use only the spare parts approved by the manufacturer.
- Do not use more than one mattress in the crib.
- Be aware of the threat posed by a burning cigarette, open flame or other sources of high temperature, such as electric heaters, gas water heaters, etc., in the near vicinity of the crib.
WARNINGS FOR BEDSIDE SLEEPER:
- DO NOT use the bedside sleeper if any parts are missing, damaged, or broken. Contact Lionelo for replacement parts and instructional literature if needed. DO NOT substitute parts.
- The distance from the floor of the adult’s bed for which the bedside sleeper is intended is between 54.6 cm and 67.3 cm.
- The bedside sleeper is intended only for standard adults’ beds. Do not use the product with waterbeds or rounded beds.
- Do not use other mounting systems than described in the manual.
- Never use the bedside sleeper if it is inclined.
- To avoid suffocation risk, always attach the bedside sleeper to the parents’ bed with the use of mounting systems described in the manual.
- There must not be any free space between the lower part of the bedside sleeper and adult bed’s mattress.
- Before every use, check the bed mounting system tension. To do so, try to pull the bedside sleeper away from the parents’ bed.
- If there is free space between the bedside sleeper and adults’ bed, DO NOT USE the product.
- The gap between the bedside sleeper and adults’ bed must not be filled with pillows, blankets and other items.
- DANGER! Always completely raise the drop side when not attached to the adult’s bed.
- WARNING: To avoid hazards from the child’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must not be higher than the adult bed mattress.
- WARNING: To avoid the risk of your child being strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.
Product components (Fig. B)
- Mattress
- Mounting straps
- Top handrail
- Carrycot
- Connecting element
- Height adjustment lever
- Accessory basket
- Frame leg
- Folding side
Assembly instructions
- Unfold the frame legs (fig. 1).
- Insert the connecting element into the respective receptacle under the carrycot to secure the element with a distinct click (fig. 2). Mind the metal tabs (A, fig. 2), which should engage the respective holes by pressing them in.
- Install the accessory basket (fig. 3). The assembly is secured when the distinct click is heard. Mind the metal tabs (A, fig. 3), which should engage the respective holes by pressing them in.
- Put the rubber loops of the accessory basket over the metal tabs (fig. 3a).
- Place the mattress in the crib (fig. 4).
- Pass the mounting straps under the carrycot through the respective holes in the frame (fig. 5a), then into the buckles, and pull them taut (fig. 5b).
- The crib is correctly assembled.
Bedside sleeper function
To use the product as a bedside sleeper, it needs to be converted. The
procedure:
-
Undo the zippers on both ends of the folding side (fig. 7).
-
Slide the locks (fig. 8a) to release the railing retainer (fig. 8b).
-
Lower the folding side of the carrycot.
-
Put the crib to the side of the adult’s bed and set the crib’s height so that the top of the bed’s mattress is level with – or no more than 2 cm above – the top edge of the folding side.
Caution! When used as a bedside sleeper, the carrycot’s bottom must be parallel to the ground. There shall be no difference in height between the crib’s ends. -
Pass the crib’s mounting straps under the bed’s mattress and hook the ends over the adult’s bed frame on the opposite side of the bed. The ends must be upright between the bed frame and the mattress.
-
Secure the mounting straps to the crib using the clasps (fig. 10b).
-
Tighten the mounting straps and make sure this keeps the crib stable and firmly attached to the adult’s bed.
CAUTION: Before each use, make sure there is no gap between the adult’s
bed mattress and the side of the crib.
WARNING: This product can only be used with beds and/or mattresses which
have straight edges. Do not use this product with any beds and/or mattresses
which are rounded or with water beds.
Height setting
To change the crib’s height, press the height adjustment levers on both ends
of the crib (fig. 11) and set the carrycot at the desired height.
There are seven crib height settings available. The crib allows setting a
different height of each of its ends.
WARNING: The maximum permitted tilt of the crib carrycot is a difference
of two setting levels. Always keep the baby’s head in the crib on the higher
end of the carrycot.
Wheel brake
To lock the crib wheels, press down the brake tabs on each of the wheels (fig.
12a). To release the wheels, lift the brake tabs (fig. 12b).
Disassembly instructions
-
Remove the mattress from the crib.
-
Undo the carrycot covering zippers at the top part of the crib frame (fig. 13).
-
Release the straps under the carrycot (fig. 5a & 5b) and remove the covering (fig. 14b).
Caution! The carrycot covering can be washed by undoing the hook and loop fasteners (A, fig. 14a), removing the folding side brace, and removing the covering (fig. 14b). -
Remove the connecting element from under the carrycot by pressing the release buttons on both ends of the crib (A, fig. 15).
-
Remove the accessory basket by pressing the release buttons on each of the basket’s legs (A, fig. 16).
-
Fold down the crib frame legs (fig. 17).
Cleaning and maintenance
- The carrycot covering and the mattress case can be hand washed in 30°C.
- Clean the metal and plastic parts with a damp cloth and a mild detergent.
- Never clean any part of the crib with abrasives, ammonia, bleach, or alcohol.
- Store the crib in a dry place, away from heat and moisture. Avoid direct exposure to sunlight.
This product has been tested and meets all requirements of EN
1130:2019+AC:2020 and EN 16890:2017+A1:2021
These pictures are for reference only, the actual appearance of the products
may differ from the pictures.
Detailed warranty conditions are available on the website:
www.lionelo.com