Wenhui 2AR95WHK02 Intelligent Switch Remote Control Switch User Manual

Wenhui 2AR95WHK02 Intelligent Switch Remote Control Switch

Product Information

Specifications

• Compliance : Part 15 of FCC Rules
• Radiation Exposure Limits: FCC-Approved
• Minimum distance between radiator and body: 0cm

Product Usage Instructions

• Installation
  Ensure the device is installed in a location where the minimum distance of 0cm between the radiator and your body is maintained.

• Operation
  Operate the device in accordance with the manufacturer’s guidelines. Avoid making any changes or modifications that are not explicitly approved by the manufacturer to ensure continued compliance and safe operation.

• Maintenance
  Regularly check for any signs of damage or wear. Keep the device clean and free from dust or debris for optimal performance.

Controller Installation

1. Connect the controller in series with the circuit of the lamp. Connect the firewire to L and the neutral wire to N. INPUT is connected to the input (input end) , OUTPUT is connected to the outout ( lamp end: As shown below:
2. After connecting the controller, it can be fixed in the appropriate position with the supplied double-sided tape or screw package.

Installation

Remote control AC installation

• Switch A
  Open the cover of the remote control switch and install thebattery into the battery compartment, then cover the uppercase; As shown below: Note : The switch button is in the centre of the panel, if it is not operated correctly, it will not be sensitive enough for use.

• Switch B
  Slide open the back panel of the remote control switch, put the battery in, and then close the back panel; As shown below:

Note : The panel has two switch buttons, which need to be coded separately to control the same controller.

Parametric

Controller

1. Working voltage: AC100-250V 60HZ/50HZ
2. Working frequency: 433MHZ
3. Power consumption in standby mode: <0.3W
4. Load power: LED200W
5. Receiving sensitivity: – 108dBM
6. Working way: wireless control
7. Coding way: learning code
8. Modulation: ASK
9. Working temperature : -10°C-+70°C
10. Size : 723826 (mm)
11. Load current: 10A

Remote Control

Switch A

1. Working voltage: DC3.0V
2. working frequency : 433MHZ
3. Power consumption in standby mode : <luA
4. Transmitter power: <10mW
5. Working way: wireless control
6. Coding way : EV1527 learning code
7. Modulation: ASK
8. Working temperature: -10°C-+70°C
9. Size : 868615mm
10. Battery :12V 27A

Switch B

1. Working voltage: DC3.0V
2. working frequency: 433MHZ
3. Power consumption in standby mode : <1uA
4. Transmitter power: <10mW
5. Working way: wireless control
6. Coding way : EV1527 learning code
7. Modulation: ASK
8. Working temperature: -10°C-+70°C
9. Size: 1157014mm
10. Battery: 2 AAA batteries 1.5V 1200mA

Pairing method

The combo products has been successfully paired at the factory.

1. Pairing code

2. Automatic pairing method of power on: When the controller is not paired with the remote control switch (after the controller completes the code clearing), the indicator light starts flashing and enters the code matching mode. At this time, press the remote control switch twice, and the lamp is controlled to successfully code matching;

3. Manual pairing method: Long press the controller code key for 3 seconds and the indicator light starts flashing and enters the code matching mode.
   After the code is successfully switched off, the control state will be memorized, and automatically restore the previous state after power on.

4. Clearing mode
   Manual code clearing method: Long press the controller key for 10 seconds and the indicator light flashes twice to clear the code successfully.

Cautions

1. Do not cut off the power of the original switch, the combination of the switch and controller can be operated normally.
2. If you want to add more than one switch on the same controller, you need to match the code with the controller; if you want to replace the switch, you need to clear the code of the controller and re-match the code with the new switch.
3. In the case that the switch and the controller match wrongly, please clear the code of the wrong controller and re-code it.
4. Please don’t operate in electricity and use it after testing.
5. Please change the battery in time (the remote control distance wil become closer when the voltage is insufficient)
6. When using wireless electronic products, please avoid metal masks, large electronic equipment, electromagnetic fields, etc., which have strong interference sources, to avoid remote control and short receiving distance or not working properly.
7. Do not use this electronic product abnormally. Abnormal use will reduce product performance and longevity. Seriously damaged products may bring security risks.

FCC

Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications.

However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.

FAQ

Q: Can I modify the device?
A: No, any changes or modifications not approved by the manufacturer may void your authority to operate the equipment.

Q: What should I do if I experience interference?
A: If you experience interference, ensure that the device is not causing harmful interference itself. If interference persists, contact the manufacturer for further assistance.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>