VIDEX VLE-BH12 LED Blukhead Light Instruction Manual
- June 9, 2024
- VIDEX
Table of Contents
VLE-BH12 LED Bulkhead Light
Instruction Manual
LED BULK’ EAD LIGHT
VLE-BH12 LED Bulkhead Light
LED BULKHEAD LIGHT
-
Rated voltage, frequency.
-
Rated power.
-
Color temperature.
-
Not compatible with lighting dimmer.
-
Rated luminous flux.
5.1. Luminous flux of luminaries
5.2. Luminous flux of light source (360°).
5.3. This product contains a light source of energy efficiency class. -
Color Rendering Index.
-
Beam angle of luminaries.
-
Nominal lifetime.
-
Protection against dust and water jets provided.
-
ON/OFF cycles.
-
No perceptible flicker to the human eye.
-
Ultraviolet-free.
-
Mercury-free.
-
Compliance with standards of eco-design and energy labeling in force from Sep 01, 2021.
-
Working temperature.
-
Product meets requirements of EU directives.
-
The minimum distance from the illuminated object.
-
Class Il. Protection against electric shock is provided not only through basic insulation, but also double or reinforced insulation.
-
Product can be installed and operated in/on a surface made of materials which are normally flammable.
-
For outdoor use only.
-
Replace the defective lamp cover immediately. Don’t use the product if the outer bulb is cracked or broken.
-
LED light source can be replaceable by the manufacturer’s authorized person.
ENVIRONMENTAL PROTECTION -
Pursuant to the provisions of the WEEE Act, it is forbidden to put waste equipment marked with the symbol of a crossed bin together with other waste. The user, wishing to get rid of electronic and electrical equipment, is obliged to return it to a waste equipment collection point. There are no hazardous components in the equipment that have a particularly negative impact on the environment and human health.
PRODUCT’S PURPOSE AND APPLICATION
This product is intended for illumination of the public or industrial space,
also of the warehouses and building structures.
INSTALLATION INSTRUCTIONS
Installation must be performed by an electrician or authorized person.
Read the user’s manual prior installation. The light source and control gear
are an integral unit. Any assembly or maintenance activities to be done with
power supply OFF. To install the LED fixture:
- Press down on the decorative cover from both sides and remove it (Fig.11), (Fig.1.2);
- Remove the protective cover from the terminal box (Fig.2);
- Connect the L, N wires to the ~ 230V, 50 / 60Hz mains using a screw terminal (Fig.3) and fasten the protective cover of the terminal box back (Fig.4). The ends of the wires must be insulated to the appropriate length:
- Fix the luminaire using the mounting hardware (Fig.5);
- Install the decorative cover until it clicks into place (Fig.6.1), (Fig.6.2). Before the first use it is necessary to verify that mechanical installation and electric connection are carried out correctly. The manufacturer reserves the right to provide technical changes and improvements without notifying the user.
FUNCTIONAL CHARACTERISTICS
This product should be used outdoor only.
MAINTENANCE & SAFETY INSTRUCTIONS
Any maintenance work must be performed when the power supply is cut OFF and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. LED
fixture may heat up to a higher temperature. Product can only be supplied by
rated voltage or voltage within the range provided. It’s forbidden to use the
product with the damaged electric wiring or places of connections.
ATTENTION! Do not look directly at LED light beam. It’s forbidden to use
the product with damaged cover. Product must not be used in unfavorable
conditions, e.g. explosive air atmosphere, fumes, or chemical fumes, etc. The
light source in the luminaire can be replaced by a person authorized by the
manufacturer as part of service work. If the light source is damaged, contact
the manufacturer for service. Used or damaged product should be disposed of
in accordance with applicable regulations.
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
Allegro Opt Sp. z 0.0. shall not be responsible for any damage resulting from
the failure to follow these instructions. The manufacturer reserves the right
to make changes in the manual.
Allegro Opt Sp. z 0.0., Handload
23, 05-120 Legion, Poland.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>