VIDEX VL-FSO-205 LED Solar Floodlight User Manual
- June 9, 2024
- VIDEX
Table of Contents
VL-FSO-205 LED Solar Floodlight
User Manual
TECHNICAL PARAMETERS
INDEX: VL-FSO-205
Lamp | Luminous flux | 600 Lm |
---|---|---|
Color temperature | 5000 K | |
LED type | SMD 2835 | |
Color Rendering Index | Ra>80 | |
Beam angle | 90° | |
Dimensions | 128x145x40 mm | |
Colour | Grey / Szary / Grau | |
Battery | Power | 20 W |
Type | LiFePO4 | |
Nominal voltage | 3.2 V | |
Nominal capacity | 5 Ah | |
Solar Panel | Pm | 10W |
Vmp | 6.0V | |
Imp | 1.6A | |
Voc | 7.08V | |
Isc | 1.8A | |
Dimensions | 350x280x17 mm | |
Max. system voltage | 1000V | |
STC | 1000W/M2, AM1.5; |
25°C
Remote controller| Infrared, 2*AAA powered
Cable| lm, 1.5mm2
Full charge| 5-8 h / c / st. (sunny weather / sioneczna pagoda/ sonniges
Wetter)
Full discharge| 512 h
Dust and moisture protection| IP65
---|---
Recommended mounting height| 3m
LED SOLAR FLOODLIGHT
- Battery capacity.
- Protection against dust and water jets provided.
- Warranty period.
- Color temperature.
- Nominal lifetime.
- No perceptible flicker to the human eye.
- Protection against mechanical impacts.
- Working temperature range.
- Product meets requirements of EU directives.
ENVIRONMENTAL PROTECTION
- Pursuant to the provisions of the WEEE Act, it is forbidden to put waste equipment marked with the symbol of a crossed bin together with other waste. The user, wishing to get rid of electronic and electrical equipment, is obliged to return it to a waste equipment collection point. There are no hazardous components in the equipment that have a particularly negative impact on the environment and human health.
PRODUCT’S PURPOSE AND APPLICATION
This product is intended for autonomous illumination of open spaces, park and private home areas.
INSTALLATION INSTRUCTIONS
Read the user’s manual prior installation. Lamp and solar panel are integral parts. Separate parts cannot use independently. It is recommended to install the solar panel such way, that the light falls perpendicular to its surface to achieve the highest efficiency (Fig.1). To install the LED solar floodlight on the surface:
- Fasten the bracket to the solar panel (Fig.2).
- Drill the holes in the surface and fix the dowels in the holes (not included). Fix the solar panel and floodlight with screws (Fig.3).
- Adjust the tilt angle and tighten the bolts on the brackets (Fig.4).
- Connect the floodlight’s and solar panel’s contacts (Fig.5). Before the first use it is necessary to verify that mechanical installation and connection are carried out correctly.
INSTALLATION OF THE REMOTE CONTROLLER
Buttons of remote controller (Fig.6):
- Turn ON
- Turn OFF
- Maximum brightness
- Increase brightness
- Decrease brightness
- Minimal brightness
- Auto mode
- Auto shutdown in 3 hours
- Auto shutdown in 5 hours
- Auto shutdown in 8 hours
It is recommended to fully charge the floodlight before first use. The floodlight will automatically turn on at night and turn off during the day.
- Press the «ON» button on the remote controller to turn on the LED floodlight.
- Use the remote control to select the desired mode and adjust the brightness of the floodlight.
AUTO mode: Press the «AUTO» button, the floodlight will give a short light
signal once. The «AUTO» button activates the automatic floodlight’s mode: the
first hour – 100% brightness; second hour – 80% brightness; from the third to
the sixth hour inclusive – 60% brightness; seventh hour – 50% brightness; from
eight o’clock to off – 30% brightness. If the ambient light is below 50 lux,
the floodlight turns on and operates automatically. The «3H» button turns on
the floodlight at night, after three hours it turns off. The «5H» button turns
off the floodlight after 5 hours. The 081-1» button turns on the floodlight,
after 8 hours it turns off. The floodlight remembers the previous setting
before the next turning on.
FUNCTIONAL CHARACTERISTICS
This product should be used outdoor only.
MAINTENANCE & SAFETY INSTRUCTIONS
Clean only with soft and dry cloths. Do not use chemical detergents. Do not
cover the product. Ensure free air access. It’s forbidden to use the product
with the damaged electric wiring or places of connections. ATTENTION! Do not
look directly at LED light beam. It’s forbidden to use the product with
damaged cover. Product must not be used in unfavorable conditions, e.g.
vibrations, explosive air atmosphere, fumes, or chemical fumes, etc. Product
with non-replaceable light source of LED type. Product cannot be fixed if the
light source becomes damaged. Used or damaged product should be disposed of in
accordance with applicable regulations.
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
Allegro Opt Sp. zo.o. shall not be responsible for any damage resulting from
the failure to follow these instructions. The manufacturer reserves the right
to make changes in the manual.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>