VIDEX VLE-SLe14 LED Street Light Instruction Manual
- June 8, 2024
- VIDEX
Table of Contents
VLE-SLe14 LED Street Light
Instruction Manual
VLE-SLe14 LED Street Light
LED STREET LIGHT
-
Rated voltage, frequency.
-
Rated power.
-
Rated luminous flux.
31. Nominal useful luminous flu (1201.
3.2. Energy efficiency class. -
Color temperature.
-
Not compatible with lighting dimmer.
-
Color Rendering Index.
-
Nominal beam angle.
-
Nominal lifetime.
-
Protection against dust and water jets provided.
-
ON/OFF cycles.
-
Protection against mechanical impacts.
-
Ultraviolet-free.
-
Mercury-free.
-
Compliance with standards of ecodesign and energy labeling in force from Sep 01, 2021.
-
Adjustable tilt angle of the fixture.
-
Working temperature.
-
Product meets requirements of EU directives.
-
The minimum distance from the illuminated object
-
Class I. A product in which protection against electric shock is provided not only by means of basic insulation but also through additional safety measures, i.e. extra protective circuit to which protective conductor of the fixed feeding installation needs to be connected.
-
Product can be installed and operated in/on a surface made of materials which are normally flammable.
-
For outdoor use only.
-
Replace the defective lamp cover immediately. Don’t use the product if the outer bulb is cracked or broken.
-
LED light source cannot be replaced.
-
Danger of electric shock.
ENVIRONMENTAL PROTECTION
- Pursuant to the provisions of the WEEE Act, it is forbidden to put waste equipment marked with the symbol of a crossed bin together with other waste. The user, wishing to get rid of electronic and electrical equipment, is obliged to return it to a waste equipment collection point There are no hazardous components in the equipment that have a particularly negative impact on the environment and human health.
PRODUCTS PURPOSE AND APPLICATION
This product is intended for illumination of parks, streets and building structures.
INSTALLATION INSTRUCTIONS
Installation must be performed by an electrician or authorized person. Read the users manual prior installation. Any assembly or maintenance activities to be done with power supply OFF.
-
To install the LED street light on the surface:
11. Drill 4 holes in the surface and fix the dowels in the holes (not included) (Fig11):
1.2. Connect the L. N. wires to the – 230V, 50 / 60Hz mains using an outdoor junction box and screw terminal (not included) (Fig1.2). The ends of the wires must be insulated to the appropriate length:
1.3. Fix LED street light with screws (Fig.1.3);
1.4. Adjust the tilt angle and tighten the mechanism (Fig1.4). -
To install the LED street light on the pole (not included):
21. Connect the L. N, **wires to the – 230V, 50 / 60Hz mains using an outdoor junction box and screw terminal (Fig.2.1). The ends of the wires must be insulated to the appropriate length;
2.2. Fix LED street light on the pole and tighten all mounting screws securely (Fig.2.2).The diameter of the mounting hole is indicated on the package;
2.3.** Adjust the tilt angle and tighten the mechanism (Fig.2.3). Before the first use it is necessary to verify that mechanical installation and electric connection are carried out correctly.
FUNCTIONAL CHARACTERISTICS
This product should be used outdoor only.
MAINTENANCE & SAFETY INSTRUCTIONS
Any maintenance work must be performed when the power supply is cut OFF and
the product has cooled down.
Clean only with soft and dry cloths. Do not use chemical detergents. Do not
cover the product Ensure free air access. LED product may heat up to a high
temperature. Product can only be supplied by rated voltage or voltage within
the range provided. It’s forbidden to use the product with the damaged
electric wiring or places of connections. ATTENTION! Do not look directly at
LED light beam. It’s forbidden to use the product with damaged cover. Product
must not be used in unfavorable conditions, e.g. explosive air atmosphere,
fumes, or chemical fumes, etc. Product with non-replaceable light source of
LED type. Product cannot be fixed if the light source becomes damaged. Used or
damaged product should be disposed of in accordance with applicable
regulations.
Failure to follow these instructions may result in e.g. fire, bums, electrical
shock, physical injury and other material and non-material damage. Allegro Opt
Sp. z o. o. shall not be responsible for any damage resulting from the failure
to follow these instructions. The manufacturer reserves the right to make
changes in the manual.
Allegro Opt Sp. z o.o., Handlowa
23, 05-120 Legionowo, Poland.