CLAGE Twin I Instantaneous Water Heater Instructions
- August 18, 2024
- CLAGE
Table of Contents
- CLAGE Twin I Instantaneous Water Heater
- E-convenience instant water heater set Twin
- Amendment Twin GA
- Supplements
- Chapter How to use:
- Chapter Remote control:
- Chapter CLAGE App:
- Optional supplements (only if not already pre-assembled)
- Installing the appliance
- Chapter 6. Electrical connection:
- Chapter 7. Initial operation
- FAQ
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CLAGE Twin I Instantaneous Water Heater
INSTRUCTION MANUAL
E-convenience instant water heater set Twin
Amendment Twin GA
This amendment shows the modifications of the appliance regarding attached
manual.
This sheet has to be kept together with the manual.
Supplements
Chapter Description of the appliance:
The Twin system is for a parallel water supply to one or more tap connections
with a high hot water demand with two special programmed Twin water heat-ers.
With this special Twin software the appliances in a functional group will be
synchronized. The temperature settings will be adapted by all appliances
automatically and the consumption data can be read out by the CLAGE Smart
Control app via smart phone or tablet.
The Twin I serves in this group as a control unit and forwards all temperature
changes to the Twin II.
It can be operated directly on the device, via remote control or via the Smart
Control App with a smart phone / tablet.
Note: A slight delay in temperature change is normal.
Chapter How to use:
Settings
Temperature Limit: In group operation mode the temperature limit must be set on the same value at all appliances of the group.
Flow Limit: If a flow limit is required, it must be set the same on all appliances.
Chapter Remote control:
Registration of remote control at the instant water heater
The remote control can only be registered at the Twin I. For the Twin II the
remote control function is disabled.
Chapter CLAGE App:
The app can be registered on the Twin I via WLAN or Bluetooth. With the Twin II, registration is only possible via WLAN.
Chapter Trouble-shooting and service
| Problem | Cause | Solution |
|---|---|---|
| Temperature can be selected higher than temperature limit | Temperature limit | |
| is not set on all appliances of the group | Set the same temperature limit for |
all appliances
Optional supplements (only if not already pre-assembled)
Chapter 5. Installation:
Installation site
- For a group operation the water pipes of the appliances must be connected via the Tichelmann-principle. Suitable piping is already pre-assembled in the Twin cabinet.
- Both instantaneous water heaters must be installed in the Twin cabinet.
Installing the appliance
Note: Open the water supply only after the installation of both instantaneous water heaters. Otherwise water will leak from the supply lines of the missing device.
Mounting the remote control’s wall bracket
Note: Test the radio contact with closed cabinet cover before attaching the bracket.
Chapter 6. Electrical connection:
Electrical connection from below
Note: The dimensions for stripping of the cable may vary with use of the Twin cabinet.
Chapter 7. Initial operation
A flow rate of at least 4 l/min is required to flush the water pipes and for operation.
Selection of power rating
Note: It is recommended to set the power rating at all appliances equally to ensure an optimal group operation.
Shower application
Note: In group operation the temperature limit must be set at all appliances of a group and the lock level must be activated.
CLAGE GmbH
Pirolweg 4
21337 Lüneburg
Deutschland
Telefon: +49 4131 8901-0
E-Mail: service@clage.de
Internet: www.clage.de
FAQ
Q: How should I mount the remote control’s wall bracket?
A: Test the radio contact with the closed cabinet cover before attaching the bracket.
Q: What is the minimum flow rate required for initial operation?
A: A flow rate of at least 4 l/min is required to flush the water pipes and for operation.
Q: What should I consider when selecting the power rating?
A: It is recommended to set the power rating at all appliances equally to ensure optimal group operation.
Q: How should I use the instant water heater in a shower application?
A: In group operation, ensure the temperature limit is set on all appliances within the group and activate the lock level.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>