VIDEX VL-LED LED Waterproof Batten Light Instructions
- June 8, 2024
- VIDEX
Table of Contents
LED WATERPROOF BATTEN LIGHT
ED WATERPROOF BATTEN LIGHT
-
Rated voltage, frequency.
-
Rated power.
-
Color temperature.
-
Not compatible with lighting dimmer.
-
Rated luminous flux.
5.1. Luminous flux of luminaries.
5.2. Luminous flux of light source [360°).
5.3. This product contains a light source of energy efficiency class. -
Color Rendering Index.
-
Beam angle of luminaries.
-
Nominal lifetime.
-
Protection against dust and water jets provided.
-
ON/OFF cycles.
-
No perceptible flicker to the human eye.
-
Ultraviolet-free.
-
Mercury-free.
-
Compliance with standards of ecodesign and energy labeling in force from Sep 01, 2021.
-
Operating temperature range.
-
Product meets requirements of EU directives.
-
The minimum distance from the illuminated object.
-
Class I. A product in which protection against electric shock is provided not only by means of basic insulation but also through additional safety measures. i.e. extra protective circuit to which protective conductor of the fixed feeding installation needs to be connected.
-
Product can be installed and operated in/on a surface made of materials which are normally fiammable.
-
Product can be used either indoors or outdoors.
-
Danger of electric shock.
-
Replace the defective lamp cover immediately. Don’t use the product if the outer bulb is cracked or broken.
-
The light source can be replaced by the end user.
-
The control gear cannot be replaced.
ENVIRONMENTAL PROTECTION -
Pursuant to the provisions of the WEEE Act, it is forbidden to put waste equipment marked with the symbol of a crossed bin together with other waste. The user, wishing to get rid of electronic and electrical equipment, is obliged to return it to a waste equipment collection point. There are no hazardous components in the equipment that have a particularly negative impact on the environment and human health.
PRODUCTS PURPOSE AND APPLICATION
This product is intended for illumination of the public or industrial space, also of the warehouses and building structures.
INSTALLATION INSTRUCTIONS
Installation must be performed by an electrician or authorized person. Read the user’s manual prior installation. Any assembly or maintenance activities to be done with power supply OFF. To install the LED batten light:
- Drill two holes; Fix the mounting clamps using self-tapping screws (Fig.1);
- To connect the batten light you need to unscrew 4 screws and remove the cover (Fig.2) ;
- Lead the wire through the cable gland and connect the L, N and wires to the – 230V, 50 / 60Hz mains using a terminal box (Fig.3). The ends of the wires must be insulated to the appropriate length.
- Replace the cover and tighten the 4 screws. Clamp the cable gland (Fig.4):
- Fix the LED batten light in mounting clamps (Fig.5). FUNCTIONAL CHARACTERISTICS Product can be used either indoors or outdoors.
MAINTENANCE &SAFETY INSTRUCTIONS
Any maintenance work must be performed when the power supply is cut OFF and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. Product
may heat up to a higher temperature. Product can only be supplied by rated
voltage or voltage within the range provided. It’s forbidden to use the
product with the damaged electric wiring or places of connections.
ATTENTION! Do not look directly at LED light beam. Its forbidden to use
the product with damaged cover. Product must not be used in unfavorable
conditions, e.g. explosive air atmosphere, fumes, or chemical fumes, etc. The
light source in the LEO batten light can be replaced by the end user. If the
product is damaged. contact the manufacturer for service. Used or damaged
product should be disposed of in accordance with applicable regulations.
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
Allegro Opt Sp. z o. o. shall not be responsible for any damage resulting from
the failure to follow these instructions. The manufacturer reserves the right
to make changes in the manual.
Allegro Opt Sp. z o.o., Handlowa 23, 05-120 Legionowo, Poland.