VIDEX VLF-H055D 500 MAX Lumis Headlamp User Manual
- June 8, 2024
- VIDEX
Table of Contents
VIDEX VLF-H055D 500 MAX Lumis Headlamp
TECHNICAL PARAMETERS
| HIGH* | LOW | MOON | STROBE | RED ON | RED FLASH | ||
|---|---|---|---|---|---|---|---|
| 1 | 500 Lm | 140Lm | 25Lm | 475Lm | 0,6Lm | 0,6Lm | |
| 2 | 2h 40min | 6h | 38h | 6h | 22h | 44h | |
| 3 | 115m | 60m | 20m | 110m | – | – | |
| 4 | 3280cd | 952cd | 92cd | 3200cd | – | – | |
| 5 | 5000 K | ||||||
| 6 | 2x CREE XTE 5W | ||||||
| 7 | Li-pol 1200mAh 3.7V / 3x AAA | ||||||
| 8 | Type-C, 5V 0.5А | ||||||
| 9 | 3 h | ||||||
| 10 | IP65 | ||||||
| 11 |  | 1 m | ||||||
| 12 | 60x45x48 mm | ||||||
| 13 | 72 g |
Li-Pol Rechargeable battery or 3xAAA
OVERVIEW
TECHNICAL PARAMETERS
- Output.
- Runtime.
- Distance.
- Intensity.
- Correlated color temperature.
- LED type.
- Compatible battery.
- Charging port type, voltage and current.
- Charging time.
- Dust and moisture protection level.
- Impact resistance.
- Product sizes.
- Product weight (without battery).
- Color: black.
- Optical system type: textured refl vector
- Materials: polyamide, polycarbonate
Note: Output, Runtime, Distance, Intensity and Charging time results have been tested with a stock battery VLF-B12 1200 mAh 3.7V. The above mentioned parameters may vary between environments and actual batteries used.
The High mode runtime is the accumulated time, including reduced output levels with the overheat protection enabled.
MAIN FEATURES
- Maximum brightness 500 lumens with two LEDs
- Compatible with Li-Pol battery pack or with 3x AAA batteries
- Built-in motion sensor for swift turning on/off
- Water resistance IP65 (protected from all precipitation)
- Type-C charging port
- Red light preserves night vision
INCLUDED
- Headlamp VLF-H055D;
- Charging cable;
- Nylon headband;
- Li-Pol rechargeable battery VLF-B12
- Videx alkaline battery AAA 3pcs
LIGHTING MODES
- High – maximum brightness
- Low – low brightness
- Moon – minimum brightness
- Strobe – flashing light
- Red on – constant red light
- Red flash – flashing red light
OPERATING INSTRUCTION
Short press button – turn on the light, switch between modes and turn off the
light cyclically.
Long press (0.5 seconds) button with the light switched on -remember current
mode and switch the light off . Short press again –turn on the last remembered
mode.
Short press button with the light switched off – activate the sensor HIGH
mode. A blue indicator informs that the sensor is activated. After that, you
can turn on/off the light by a hand waves closely to the device
Short press button with the light switched on – remember current lighting mode
and later switch it on/off by the sensor.
BATTERY STATUS INDICATION
Press and hold the button for 0.5 seconds to see the battery status.
The indication will last for 3 seconds.
- 4 divisions – 100-80% charge;
- 3 divisions – 79-50% charge;
- 2 divisions – 49-25% charge;
- 1 division – 24-1% charge.
- 1 division flashes – battery discharged.
CHARGING
ATTENTION! AAA batteries cannot be charged.
Plug the USB-A socket of the charging cable into electrical outlet.
Switch off the light, open the protective cover and connect the charging cable
to the fl ashlight port.
When charging, the divisions fl ash indicating the current battery level.
When fully charged, all 4 indicator bars are constantly on.
After a full charge, unplug the charging cable and close the protective cover
to prevent water and dust from entering to the headlamp body.
© The original rechargeable batteries are supplied charged and can be used immediately after purchase, however it is recommended that the battery be fully charged before fi rst use. The battery needs to be charged in time before it is completely discharged. During long periods of storage, it is recommended to keep the battery charging level at about half capacity to extend its service life.
BATTERY REPLACEMENT
- Fully open the tilt angle adjusting mechanism;
- Pull up the lock located behind the control buttons and open the back cover;
- Insert the battery/s according to the diagram shown on the inside of the battery compartment;
- Close the cover until it snaps and test the headlamp.
MAINTENANCE AND SAFETY INSTRUCTIONS
- For long-term storage, it is necessary to remove the batteries from the headlamp to avoid leakage.
- It is recommended to keep the battery contacts clean to maintain original performance.
- ATTENTION. Avoid direct shining into eyes as it may cause the eyes damage.
- Do not charge AAA batteries. It may cause into leakage and damage the device.
- Do not use batteries other than those specified in the technical specifications.
- Do not disassemble the sealed body of the headlamp as this may compromise performance and void the warranty.
- Keep out of the reach of children.
WARRANTY
The warranty for the headlamp is 2 years, for the VLF-B12 battery – 1 year. The warranty does not cover accessories. The LED source inside the headlamp is not replaceable. If the LED fails, the whole headlamp should be replaced. During the warranty period, a faulty headlamp and the VLF-B12 battery can be exchanged or returned with a prove of purchase and all accessories saved.
The following does not apply with the scope of limited warranty:
- Misuse the product and cause the products integral components – Unauthorized disassemble or the presence of deep mechanical damage to the product;
- Damage due to force majeure.
ENVIRONMENTAL PROTECTION
Pursuant to the provisions of the WEEE Act, it is forbidden to put waste
equipment marked with the symbol of a crossed bin together with other waste.
The user, wishing to get rid of electronic and electrical equipment, is
obliged to return it to a waste equipment collection point. There are no
hazardous components in the equipment that have a particularly negative impact
on the environment and human health.
The producer shall not be responsible for any damage resulting from the
failure to follow above instructions. The producer reserves the right to make
updates of this user’s manual
Producer/Producent: Allegro Opt Sp. z
o.o., Handlowa 23, 05-120 Legionowo,
Poland. Made in P.R.C.