LEXON LH87 Luma M LED Light Instruction Manual
- June 3, 2024
- LEXON
Table of Contents
LH87
LUMA M
Design by Manuela Simonelli & Andrea Quaglio
Scan to access the full user manual
https://www.lexon-design.com/manual/luma-m.pdf
IN THE BOX
1x Luma M
1x USB Type-C charging cable
1x User manual
PRODUCT OVERVIEW
- Touch area (Lighting function)
- Lamp
- BT Button (connection between Luma M lamps)
- Reset key
- Receiver for wireless charging
- LED indicator (battery & charging status)
- USB Type-C charging port
CHARGING
We recommend you to fully charge the battery before using Luma M for the first
time.
The initial full charge should take approximately 3 hours via USB charging and
4 hours via wireless charging.
OPERATING INSTRUCTIONS
Setting up one Luma M lamp
- Touch the top of the lamp to turn it ON.
- There are 9 colors options you can select by simply touching the top of the lamp.
- To adjust brightness, touch the top area until you reached the desired brightness then release.
- To turn OFF the light, wait 3 seconds after the color selection then touch again.
The last color set will be remembered for next time.
Pairing several Luma M lamps (Interconnection network)
Pairing Luma M with one or multiple Luma M lamps does not require any third-
party software/device.
To enjoy the multiple bulbs synchronization feature, follow below
instructions:
1. Press and hold the BT button at the bottom of each lamp for 3 seconds to
turn ON the communication module. The Blue LED will start flashing.
2. Select one of the lamps and press the BT button twice to initiate the
multi-pairing procedure.
Once procedure is complete, all lamps will be on the same color setting.
The lamp used for connection is now identified a MASTER in the system, its LED
will keep flashing while others are turned OFF
You can now interact from any lamp the change the color, adjust brightness or
turn ON & OFF all lamps at once.
Add one or more Luma M lamps to the network
- To add one or more Luma M lamps to the network, simply to it (them) ON by pressing and holding the BT button on each unit for 3 seconds.
- Press once on the pairing button of any lamp from the existing network (repeat the procedure with any new device).
Exclusive LOCK NETWORK feature
Luma M is equipped with a unique locking system allowing only One lamp to
control all others, preventing any change of color, brightness or even turn
ON/OFF to be made from any other lamp in the network. The main lamp (MASTER)
is the only one to control the network. All other lamps are becoming SLAVES.
To enable LOCK function, take the MASTER units and follow below instructions:
- Press 5 times on the BT MASTER device button, it will send signal to ALL other lamps to LOCK.
- In LOCK mode, only MASTER interact with other lamps. Its LED is double flashing every 3 seconds.
- Network can be unlocked by quickly pressing 5 times on the BT button from the MASTER lamp
SAFETY PRECAUTIONS
- IPX4 water resistant device, resistant to rain, splash, and spray water.
- Never immerse your device in water to avoid internal short circuit, overheating, fire, deformation or even explosion of the battery.
- Do not store your device in very hot or cold areas. It is recommended to use your device at room temperatures.
- Do not attempt to service, repair or disassemble the device yourself.
- Make sure to respect the technical specifications for charging and never use a power adapter delivering more voltage output than the one indicated to avoid any irreversible damage to the internal circuit (DC Input: 5V)
- Do not place the Luma M case on the wireless charger when conductive materials, such as metal objects and magnets, are placed between the Luma M case and the wireless charger.
- Use only certified wireless chargers.
PRODUCT SPECIFICATIONS
Material: Aluminium/ABS
Weight: 0.34 lbs / 153 g
Dimensions: 03.66 x 4.25″ / 09.3 x 10.8 cm
Max lumen output: 45 Im
Color temperature:
Warm white: 3000-3500
Cold white: 6800-7200
Color temperature: 3000- 7200k
Battery voltage: 3.7V
Normal usage time
Lamp ON not connected to network:
Up to 24h (Brightness at 50%)
Lamp ON connected to network:
Up to 12h (Brightness at 50%)
Bluetooth® range: 10m
Frequency range: 2402M-2480MHZ
Input port: DC 5V
Wireless input: 5W
Battery type: Li-polymer
Battery capacity: 900 mA
Charging system: USB Type-C or Supports wireless charging
Charging time (USB Type-C): approx. 3 hours
Charging time (wirelessly): approx. 4 hours
Operating temperature: +50°C-10°C –
International warranty: 1 year
EUROPEAN UNION
CE DIRECTIVE
LEXON hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the RED Directive 2014/53/EU.
The original EU declaration of conformity may be found at https://www.lexon-
design.com/assets/certifications-ce-lumam.pdf
UK CONFORMITY ASSESSMENT
The object described above is in conformity with the essential requirements
and other relevant provisions of the UK Radio Equipment Regulations 2017 (SI
2017/1206).
The original UK declaration of conformity may be found at:
https://www.lexon-design.com/assets/certifications-ukca-lumam.pdf
RF Specification
Bluetooth: 2402-2480 MHz
WPT: 110 kHz-148 kHz (RX)
BT transmitter power: 2.34dbm
DISPOSAL AND RECYCLING INFORMATION
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies: electrical and electronic devices may not
be dis-posed of with domestic waste. Consumers are obliged by law to return
electrical and electronic device at the end of their service lives to the
public collecting points set up for this purpose or point of sale. Details to
this are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the package indicates that a product is
subject to these regulations. By recycling, reusing the materials or other
forms of utilizing old devices, you are making an important contribution to
protecting our environment.
USA – FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation. Notice:
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
FCC RF exposure statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
CANADIAN COMPLIANCE STATEMENT
This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may
cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
125, Avenue des Champs-Elysées – 75008 Paris – FRANCE
All brands or product names are or may be trademarks or their respective
owners.
Pictures and specifications are not contractual. Assembled in China.
Iexon-design.com I @lexondesign
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>