LEXON LH94 Portable Lamp Lantern Instructions
- May 15, 2024
- LEXON
Table of Contents
LH94 LANTERN
LH94 Portable Lamp Lantern
Design by Alain Berteau
IN THE BOX
1x LED lamp with built-in Qi wireless charger
1x USB-C cable
1x User manual
PRODUCT OVERVIEW
- Lighting surface
- Wireless charging surface
- Touch button
- LED indicator for charging status
- Input port
- LED indicator for wireless charging status
LAMP FEATURES
- Turn ON the lamp by touching the touch button (3).
- Change the light color (9 colors options) by simply touching the touch button (3).
- Adjust the brightness by pressing and holding the touch button (3).
- To turn OFF the light, wait 3 seconds after the color selection then touch (3) again.
The last color set will be remembered for next time.
Note: If you want to set Lantern in cool and warm light mode only,
quickly tap 3 times on the touch area (3). To return to full set lighting
mode, repeat the procedure.
WIRELESS CHARGING
Important note: To get your Lexon’s device properly operating, make sure to
use a DC 9V-2A power adapter (not included) or a Quick Charge 3.0 power
adapter (not included).
To enjoy fast wireless charging* at 15 W, make sure you use a USB power
adapter that delivers at least 30 W.
If the input power is insufficient, the lamp will flash slowly in orange.
-
Only mobiles devices that support wireless charging can be charged using this feature. Charging speed or efficiency may vary depending on the environment, the device being charged and its battery capacity.
Lantern is compatible with all Qi-enabled devices.- Make sure your lamp is connected to a power source that delivers sufficient power .
- Place the mobile device supporting wireless charging face up at the center of the wireless charging surface.
| LEDs (4/6) & Lamp (1) indicators
---|---
Wireless charging initiated| Left LED is BLUE for 30 seconds
Insufficient power input| LED lamp start flashing slowly in orange
Foreign Object Detected| Left LED is RED and starts blinking quickly
Battery charging| Right LED is RED
Fully charged| Right LED turns OFF - Once the mobile device is properly positioned and charging, the left LED on the back of the lamp will turn blue for 30 seconds then turn off.
SAFETY PRECAUTION
- The light source of the lamp is an integrated LED module. Do not attempt to modify or disassemble this lamp in any way.
- Place the lamp on a dry and flat surface.
- Do not place your lamp in very hot or cold areas.
- Always clean the product with a soft cloth and do not use any cleaning materials that contain chemicals.
- Do not put metal objects or magnets between the mobile device and the wireless charging surface.
- Never place your device in water to avoid causing internal short-circuit, over-heating, fire, deformation, or even explosion of the battery.
- Keep your device out of reach of small children to prevent danger.
- Do not attempt to service, repair, or disassemble the lamp or the supplied cable yourself.
- Lexon cannot be held responsible for any malfunctions or damages resulting from failure to adhere to these instructions properly.
PRODUCT SPECIFICATIONS
Material: Synthetic leather / ABS
Weight: 1.01 lbs / 461 g
Dimensions: 5.67 x 5.67 x 8.35” / 14.4 x 14.4 x 21.2 cm
Max. lumen output: 100 lm
Light power: 5W max
Color temperature: Warm white: 3000K
Cold White: 6800K
Input port: 9V-2A, Quick Charge 3.0 Power Adapter (not included) or a DC
9V/2A power Adapter (not included).
Wireless charging output: Up to 15W
Battery type: Li-ion 5000 mAh
Battery voltage: 3.7V
Battery life: Up to 8 hours for light only
Charging time (USB Type-C): 4 hours
Operating temperature: 0°C – 35°C
international Warranty: 1 year
varies according to product use, set light intensity and selected light color
EAUROPEAN UNION
CE DIRECTIVE
LEXON hereby declares that these devices follow the essential requirements and
other relevant provisions of directives 2014/53/EU, 2014/30/EU & 2012/19/EU.
The original EU declaration of conformity may be found at: https://www.lexon-
design.com/assets/certifications-ce-lantern.pdf
UK CONFORMITY ASSESSMENT
The object described above is in conformity with the essential requirements
and other relevant provisions of the UK Radio Equipment Regulations 2017(SI
2017/1206).
This device was tested for uncontrolled environment operations. To comply with
RF exposure requirements, a minimum separation distance of 20 cm must be
maintained between the user’s body and the device.
The original UK declaration of conformity may be found at: https://www.lexon-
design.com/assets/certifications-ukca-lantern.pdf
Radiated H-Field: -13.81 dBuA/m(@10m) (for EU/UK only)
TX/RX Frequency Range: 110-148 KHz (for EU/UK only)
DISPOSAL AND RECYCLING INFORMATION
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies: electrical and electronic devices may not
be dis-posed of with domestic waste. Consumers are obliged by law to return
electrical and electronic device at the end of their service lives to the
public collecting points set up for this purpose or point of sale. Details to
this are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the package indicates that a product is
subject to these regulations. By recycling, reusing the materials or other
forms of utilizing old devices, you are making an important contribution to
protecting our environment.
USA – FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Notice: Any changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed. and operated with a minimum distance of
20cm between the radiator and your body.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-0003.
RF exposure statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. The antenna should be installed and operated with
minimum distance of 10 cm between the radiator and your body.
125, Avenue des Champs-Elysées – 75008 Paris – FRANCE
All brands or product names are or may be trademarks or their respective
owners.
Pictures and specifications are not contractual. Assembled in China.
lexon-design.com
@lexondesign