LITETRONICS FLAYM1 Flood Light Yoke Mount Instructions
- June 16, 2024
- Litetronics
Table of Contents
LITETRONICS FLAYM1 Flood Light Yoke
Installation Instructions
Compatible Models
- FL0601 – FLAYM1
- FL1001 – FLAYM2
- FL1501 – FLAYM3
- FL2552 – FLAYM4
- FL3302 – FLAYM5
SAFETY INSTRUCTIONS AND WARNINGS
- When using electrical equipment, basic safety precautions should always be observed
- This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved
- Installation should only be conducted by a qualified electrician in accordance with NEC and any relevant local building codes.
- Be certain electrical power is OFF before and during installation and maintenance.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.
WHAT COMES IN THE BOX?
- Yoke Mount
- Installation Instructions
REQUIRED TOOLS
- Allen Wrench
Part No.| Screw Size| Ground Washer| Flat Washer|
Spring Washer
---|---|---|---|---
FLAYM1| M612 (x2)| M6 (x1)| M6 (x2)| M6 (x2)
FLAYM2,
FLAYM3| M410 (x2),
M612 (x2)| M6 (x1)| M4 (x2),
M6 (x2)| M4 (x2),
M6 (x2)
FLAYM4,
FLAYM5| M818 (x4)| M8 (x1)| M8 (x4)| M8 (x4)
INSTRUCTIONS
Allen Wrench
Before Installation, carefully remove all parts from the packaging. Inspect
product for defects due to shipping.
Always turn off the power supply from main circuit breaker first!
FLOOD LIGHT YOKE INSTALLATION
-
Run the input wire through the hole in the yoke mount (watch out not to scratch the wire). See below for correct fixture and yoke mount.
-
FL0601
-
FL1001 – FL1501
-
FL2552 – FL3302
-
-
Install the mount and keep screws loose
-
FL0601
x2 M6 screws
x2 Spring washer
x2 Flat washer
x1 M6 Ground washer -
FL1001 – FL1501
x2 M4 screws
x2 M4 Spring washer
x2 M4 Flat washer
x1 M4 Ground washer
x2 M6 screws
x2 M6 Spring washer
x2 M6 Flat washer
x1 M6 Ground washer
-
FL2552 – FL3302
x4 M8 screws
x4 M8 Spring washer
x4 M8 Flat washer
x1 M8 Ground washer
YOKE MOUNT INSTALLATION
- Finish the wire connection accordingly (refer to flood light installation instructions for wiring diagram).
- Align the fixture to required angle. Tighten M6 or M8 screw after angle is confirmed. (Figure 1)
- Turn power back on.
Note: Adjustable angle is 0~+/-90 °.
(Figure 1)
Customer Support
Thank you for choosing
6969 W. 73rd Street
Bedford Park, IL 60638
WWW.LITETRONICS.COM
CustomerService@Litetronics.com or
1-800-860-3392
The information and product specifications contained in these instructions are
based upon data believed to be accurate at the time of printing. This
information is subject to change without notice and without incurring
liability. If you have questions regarding specific product details, please
contact us at 800-860-3392 or via email
at customerservice@litetronics.com.
To check for an updated version of these instructions, please visit
www.litetronics.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>