LEXON LH97 LUMA L LED Lamp Instruction Manual
- June 1, 2024
- LEXON
Table of Contents
LEXON LH97 LUMA L LED Lamp
Product Information
Specifications
- Model: LH97
- Design: LUMA L by Manuela Simonelli & Andrea Quaglio
- Components in the Box:
- 1x LUMA L lamp
- 1x USB Type-C charging cable
- 1x User manual
Product Overview
- Touch area (Lighting function)
- Lamp
- BT Button (for lamp synchronization)
- Reset key
- Receiver for wireless charging
- LED indicator (battery & charging status)
- USB Type-C charging port
Charging
We recommend fully charging the battery before initial use. Charging time is
approximately 3 hours via USB and 4 hours wirelessly.
LED Information
| Operation mode | Charging | In use | Fully charged |
|---|---|---|---|
| Status LED (Red LED) | LED indicator remains ON | LED indicator remains OFF | LED |
indicator remains OFF
Charge with USB cable
- Plug the USB Type-C cable into the charging port of LUMA L.
- Connect the USB end to a computer or DC 5V power supply charger.
Charge with Wireless Charger
- Place LUMA L at the center of the wireless charger.
- Disconnect once fully charged.
Operating Instructions
Setting up one LUMA L lamp
To set LUMA L in cool and warm light mode, tap the top area three times.
Repeat to return to full set lighting mode.
Syncing several LUMA L lamps (Interconnection network)
- To sync multiple lamps, press and hold the BT button on each lamp for 3 seconds to turn on communication.
- Select one lamp and press the BT button twice to pair all lamps.
Add one or more LUMA L lamps to the network
- To add lamps, turn them on by holding the BT button for 3 seconds.
- Press once on the pairing button of any lamp from the existing network.
Exclusive LOCK NETWORK feature
- To enable LOCK function, press the BT MASTER device button five times.
- In LOCK mode, only the MASTER lamp can interact with others.
- To unlock, press the MASTER lamp’s BT button five times quickly.
FAQs
- Q: How do I reset my LUMA L lamp?
A: To reset, locate the reset key on the lamp and press it for a few seconds until the lamp resets.
IN THE BOX
- 1x LUMA L
- 1x USB Type-C charging cable
- 1x User manual
PRODUCT OVERVIEW
- Touch area (Lighting function)
- Lamp
- BT Button (for lamp synchronisation)
- Reset key
- Receiver for wireless charging
- LED indicator (battery & charging status)
- USB Type-C charging port
FEATURES
- LED technology with 9 colors (warm white, cold white, blue, yellow, green, red, purple, light pink & light blue).
- Dimmable LED lights with memory system.
- Synchronisable LED lamp (Bluetooth mesh network).
- Suitable for outdoor use (IPX4).
- Rechargeable via wireless charging or USB Type-C.
CHARGING
We recommend you to fully charge the battery before using LUMA L for the first time. The initial full charge should take approximately 3 hours via USB charging and 4 hours via wireless charging.
LED information
Charge with USB cable
- Plug the provided USB Type-C cable into the charging port of LUMA L .
- Plug the USB end of the cable into any computer or any DC 5V power supply charger.
Charge with Wireless Charger
LUMA L has a built-in wireless charging receiver. You can charge the
battery by using a wireless charger.
- Place LUMA L at the center of the wireless charger.
- Disconnect the device once the battery has been fully charged
OPERATING INSTRUCTIONS
Setting up one LUMA L lamp
- Touch the top of the lamp to turn it ON.
- There are 9 colors options you can select by simply touching the top of the lamp.
- To adjust brightness, touch the top area until you reached the desired brightness then release.
- To turn OFF the light, wait 3 seconds after the color selection then touch again.
The last color set will be remembered for next time.
Note: If you want to set LUMA L in cool and warm light mode only, quickly tap 3 times on the top area. To return to full set lighting mode, repeat the procedure.
Syncing several LUMA L lamps (Interconnection network)
Syncing LUMA L with one or multiple LUMA L lamps does not require any third-
party software/device. To enjoy the multiple bulbs synchronization feature,
follow below instructions:
- Press and hold the BT button at the bottom of each lamp for 3 seconds to turn ON the communication module. The Blue LED will start flashing.
- Select one of the lamps and press the BT button twice to initiate the multi-pairing procedure. Once procedure is complete, all lamps will be on the same color setting.
The lamp used for connection is now identified a MASTER in the system, its LED will keep flashing while others are turned OFF.
You can now interact from any lamp the change the color, adjust brightness or turn ON & OFF all lamps at once.
Important note: Bluetooth will automatically turn off after the lamp has been off for 60 minutes. If you enable the Bluetooth® on one of your lamps to connect it to the network, but do not complete the pairing, the lamp’s Bluetooth mode will turn off after 3 minutes automatically.
Add one or more LUMA L lamps to the network
- To add one or more LUMA L lamps to the network, simply to it (them) ON by pressing and holding the BT button on each unit for 3 seconds.
- Press once on the pairing button of any lamp from the existing network (repeat the procedure with any new device).
Exclusive LOCK NETWORK feature
LUMA L is equipped with a unique locking system allowing only One lamp to
control all others, preventing any change of color, brightness or even turn
ON/OFF to be made from any other lamp in the network. The main lamp (MASTER)
is the only one to control the network. All other lamps are becoming SLAVES.
To enable LOCK function, take the MASTER units and follow below instructions:
- Press 5 times on the BT MASTER device button, it will send signal to ALL other lamps to LOCK.
- In LOCK mode, only MASTER interact with other lamps. Its LED is double flashing every 3 seconds.
- Network can be unlocked by quickly pressing 5 times on the BT button from the MASTER lamp.
To change the MASTER device
- Make sure the network is UNLOCKED
- Quickly Press the BT button on any device for 10 times, this device will become the new MASTER device. You can now LOCK and UNLOCK the network from this new device.
Important note: In LOCKED/UNLOCKED network mode, it is strongly recommended to always keep the MASTER device in charge or fully charged to get the best experience and avoid loss of control of the entire network.
Other working operations:
- To turn OFF ALL the lamps when the network is locked, double tap on the top of the MASTER device. You’ll need to tap on the MASTER again to turn all lamps back ON.
- To turn OFF only one lamp when the network is locked, long press on the BT button from more than 15 seconds until the lamp turns OFF. (This will remove the lamp from the network. Repeat the pairing procedure above to bring it back to the network)
- To reset the lamp, insert a thin object into the hole (4) under the lamp and press the key inside. A manual reset allows you to reboot your device and correct miscellaneous bugs (unrecognized device, unstable Bluetooth connection…).
LED Information
SAFETY PRECAUTIONS
- IPX4 water-resistant device, resistant to rain, splash, and spray water.
- Never immerse your device in water to avoid internal short circuit, overheating, fire, deformation or even explosion of the battery.
- Do not store your device in very hot or cold areas. It is recommended to use your device at room temperature.
- Do not attempt to service, repair or disassemble the device yourself.
- Make sure to respect the technical specifications for charging and never use a power adapter delivering more voltage output than the one indicated to avoid any irreversible damage to the internal circuit (DC Input: 5V)
- Do not place the LUMA L case on the wireless charger when conductive materials, such as metal objects and magnets, are placed between the LUMA L case and the wireless charger.
Use only certified wireless chargers.
PRODUCT SPECIFICATIONS
EUROPEAN UNION
CE DIRECTIVE
LEXON hereby declares that the device follows the essential requirements and
other relevant provisions of the RED Directive 2014/53/EU.
The original EU declaration of conformity may be found at: https://www.lexon-
design.com/assets/certifications-ce-lumas.pdf
RF Specification:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
UK CONFORMITY ASSESSMENT
The object described above is in conformity with the essential requirements
and other relevant provisions of the UK Radio Equipment Regulations 2017 (SI
2017/1206).
The original UK declaration of conformity may be found at: https://www.lexon-
design.com/assets/certifications-ukca-lumas.pdf.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
WPT:
- Radiated H-Field: -10.7 dBuA/m(@10m)
- RX Frequency Range: 110-148 KHz
Bluetooth:
- Transmitter power: 5.62dBm（for EU&UK）
- TX/RX Frequency Range: 2400-2480MHz
DISPOSAL AND RECYCLING INFORMATION
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies: electrical and electronic devices may not
be dis-posed of with domestic waste. Consumers are obliged by law to return
electrical and electronic device at the end of their service lives to the
public collecting points set up for this purpose or point of sale. Details to
this are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the package indicates that a product is
subject to these regulations. By recycling, reusing materials or other forms
of utilizing old devices, you are making an important contribution to
protecting our environment.
FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Notice: Any changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
RF exposure statements
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
CANADIAN COMPLIANCE STATEMENT
This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
RF exposure statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
125, Avenue des Champs-Elysées – 75008 Paris – FRANCE
All brands or product names are or may be trademarks or their respective
owners.
Pictures and specifications are not contractual. Assembled in China.
lexon-design.com