eziclean Map Robot vacuum Cleaner User Manual

eziclean Map Robot vacuum Cleaner

Welcome to EZI® – Make it easy Thank you for the trust you place in our EZIclean® range. We hope you are satisfied with this product and now let you take note of the following instructions for use.

• This appliance must only be used for domestic cleaning, in accordance with this user guide. Please make sure these instructions are fully understood before using the device.
• Always switch off and switch off the charger before carrying out cleaning or maintenance operations on the device.
• This device can be used by children at least 8 years old and by people with reduced physical, sensory or mental capacities, or with no experience or knowledge in this area.
• They must receive instructions on the safe use of the device and understand the risks involved. Children should not play with the device. Cleaning and maintenance should not be done by children without supervision.
• If the power cord is damaged, stop using the appliance immediately. To avoid the risk of accident, a repairer authorized by the manufacturer must replace the power cord.
• If the area to be cleaned has a balcony, a physical barrier must be used to prevent access to the balcony and to ensure safe use.
• Charge the battery and use only the original charger supplied with the device. Check that the supply voltage is the same as that indicated on the charger. Never recharge the batteries in temperatures above 30 ° C or below 0 ° C.
• Plug the charger sold with the device into a suitable outlet. Battery cells may leak under extreme conditions of use or temperature. If the liquid touches the skin, wash it off quickly with water. If the liquid gets into the eyes, immediately rinse them with clean water for at least 10 minutes. See a doctor. It’s normal for the charger to become warm to the touch when it’s charging.
• Use only accessories, consumables and spare parts recommended or supplied by the manufacturer. Avoid vacuuming hard or sharp objects, hot ashes, cigarette butts and the like. Avoid spraying or vacuuming flammable liquids, cleaning products, aerosols or their vapors.
• Stop using your device or charger if they appear to be defective. To ensure the safe and efficient use of this device, we recommend that it be serviced and repaired only by a repairer authorized by the manufacturer.
• Do not use this appliance to clean people or animals. Do not replace the robot’s batteries with non-rechargeable batteries. Disposal of end-of-life batteries
• If you dispose of the device, remove the batteries first. The device must not be connected to the mains when you remove the batteries. Dispose of batteries safely.
• Leave the device running until the device stops completely due to the fact that the batteries are completely discharged. Used batteries must be taken to a recycling point and not disposed of with household waste.
• To remove the batteries, please contact the manufacturer or follow the instructions in this guide.

Please read the following information carefully before using your robot vacuum cleaner or its accessories. Do not disassemble the device and do not try to repair it yourself. In the event of a malfunction, please contact your dealer for professional advice. Stairs: The device uses sensors to avoid falling on steps, on stairs or over an edge. In some situations, the sensors may malfunction. This device cannot detect steps that are less than 8 cm high. Steps less than 8 cm high can cause the robot to fall. Highly reflective or very dark surfaces on certain steps or stairs, such as glass or polished ceramic can cause the device to fall. If available, use the virtual wall or place a carpet on the bottom step to prevent your robot from falling. Avoid using your robotic vacuum cleaner on mezzanines, landings or elevated, undefined surfaces.

DISPOSAL
The symbol on this appliance indicates that it cannot be disposed of with household waste. You must deposit it in an electrical and electronic waste recycling center. Disposal must be carried out in accordance with local waste regulations. For further information on the treatment, recovery and recycling of this appliance, please contact your municipality, the local household waste disposal service or the retailer of the appliance. This device complies with European Directives 2006/95 / EC, 2004/108 / EC and 2011/65 / EU.

Your device

Remote control

«Start / pause» button

1. In standby mode, press this button to have your device start automatically its cleaning cycle.
2. When the device is asleep, press this button to return it to standby.
3. In operation, press this button so that the appliance stops its cleaning cycle.

Direction buttons

1. Forward ▲
   In standby or operation, press this button so that the device advances.

2. Backward ▼
   In standby or operation, press this button to make the device reverse.

3. Left ◄
   In standby or operation, press this button to make the device turn to the left.

4. Right ►
   In standby or operation, press this button to make the device turn to the right.

1. Auto button
   Press this button to start the automatic cleaning cycle.

2. Powerful button
   Press this button to star t cleaning the desired area. The suction power is more intense than in automatic mode.

3. Edge button
   Press this button to star t cleaning along the baseboards.

4. Return button
   Press this button to ask the robot to return to its charging base.

NOTE

• 2 AAA (LR03) 1.5V batteries are required
• If the remote control is not used for an extended period of time, remove the batteries.

Starting the product

1. Place the charging base against the wall 1 meter away from any obstacle. Leave 2 meters of space in front. Then connect the power cable and make sure that the LED indicator is on.

2. Switch on the device by pressing the switch. The robot emits a sound and goes into standby mode.

3. Place the water tank on the robot.
   Fill the tank with cleaning solution diluted in water. Hang the microfiber on the velcros on the water tank and clip the tank under the robot.

4. . Charging your device can be done in 2 ways.

5. Insert the adapter directly into the device and plug the other end of the power supply into the power outlet, as shown in Figure A below.

6. Press the «Return» button on the remote control or directly on the robot button, so that it automatically returns to its charging base, as illustrated in Figure B below.

Note
When using the charging base, press the «Start / Pause» button on the remote control or directly on the robot button so that it stops charging and starts cleaning. Note that this operation cannot be performed when you connect the adapter directly to the robot.

Note :

• The first time, charge the device for 12 hours.
• Regularly check that the power cable of the charging base is correctly connected. With the robot coming and going, the cable may end up unplugging slightly.
• If the robot is not used for a long time, set the switch to «O».

Automatic recharging

Active mode
All lights and buttons are on and the device is in operation. Make sure that the switch is in the «I» position. Start the robot by pressing the «start / pause» button on the remote control or directly on the robot button.

Standby mode
The charging base LED is on, the robot button is on, the device is only in standby. Press the «start / pause» button on the remote control once or directly on the robot button to start it.

Sleep mode
If the robot is not used for more than 25 seconds, it will automatically go into sleep mode.

Note :
To switch from sleep mode to standby mode, press the «start / pause» button on the remote control or directly on the device button. Press a second time to start cleaning.

The 3 cleaning modes

Automatic «Auto» button
Cleaning adapts to your room and your types of floors automatically.

Deep cleaning «Powerful» button
Place the robot on the area to clean up and it will accentuate his aspiration for this place.

Along the baseboards «Edge» button
The robot will perform its cleaning cycle starting along the baseboards.

Note

1. Once the deep cleaning or along the baseboards is finished, the robot will return to automatic mode to finish its work.
2. Whichever mode it is in, the robot will stop cleaning if you press the «start / pause» button on the remote control or directly on the device button.

Caring for your device

Cleaning the side brushes
If the side brushes are dirty, disassemble them and then wash them with clean water. Then make sure they are completely dry before reinstalling them on the device. If they are damaged, replace them with new brushes.

Note  When changing the side brushes, match the “L” and “R” signs on the side brushes to the “L” and “R” signs on the robot.

Note In order to ensure proper functioning of your device, it is recommended to change your consumables every 6 months.

Cleaning the dust container and filter

• Open the dust bin compartment and extract the bin.
• Check that the robot’s suction duct is not blocked and clean it with a cloth.
• Open the dust container and empty it, then pass it underwater if necessary. Wait until it is completely dry before reinstalling it.
• Remove the filters by blowing on them and tapping them lightly. Do not wash them with water.
• Re-assemble the filter and prefilter well before inserting them into the dust bin to avoid any malfunction.

Note
It is advisable to clean the dust container at least once a week and the filters every 15 days. Do not wash them with water. Then make sure they are properly reassembled to avoid damaging the robot.

Cleaning the water tank

• Remove the water tank from the robot and rinse it with clean water.
• Wait until it is completely dry before placing it on the robot.

Cleaning of microfibers

• Remove the microfibers and wash them with water or pass them through the machine.
• Dry them well flat.

Note
Do not use microfibers that are too wet to prevent them from flooding the ground. This could cause the robot to slip during the cleaning cycle and not function properly.
Use the water tank on hard floors only (parquet, tiles, marble and painted hard floor, etc.).

Cleaning of sensors and connectors
Use a clean, dry cloth to lightly wipe the sensors and connectors. Here is their position below:

Frequently asked questions

In case you have any doubts about the behavior of your robot, first refer to the table below.

Product condition

|

Reason / Cause

|

Solution

---|---|---

The blue light is always on

|

Normal

|

The blue light flickers slowly

|

Charging time

|

The blue light flickers fast

|

Low battery

|

Charge the robot

The red light is always on and the buzzer alarms for 20 seconds

|

Abnormal floor check

|

Re-put the host back to the floor

The red flickers slowly and the

buzzer alarms for 20 seconds

|

Abnormal collision switch

|

Check the sensitivity of the front bumper. Check whether there are foreign materials

The blue light flickers fast and the

buzzer alarms for 20 seconds

|

Overloaded drive wheel is

|

Check the drive wheel

The red and blue light fast flicker alternatively and the buzzer alarms for 20 seconds

|

Abnormal fan

|

Check the fan

The blue light flickers slowly and

the buzzer alarms continuously

|

The rechargeable power switch at the bottom is not turned on

|

Turn on the power switch at the bottom of the machine

Technical characteristic

• Dimensions (mm): 320 x 85
• Weight (kg): 2,800
• Max area : 120m2
• Navigation technology: Navig+TM – Mapped
• Max decibels : 60dB
• Battery: Lithium-ion
• Autonomy: 90 min
• Charging time: 4/6 hours
• Automatic return to base: Yes
• Technology Corner Detection: CornerTM technology
• Obstacle detection: Yes
• Watertank: Yes
• Surfaces: Tiles, Lino, Carpet, Carpets
• Capacity: 330mL
• Anti-Allergen: HEPA filter
• Remote control: Yes
• Mode of use: Targeted, Long Baseboards, Manual, Zigzag, Automatic

Enter your serial number and keep this warranty card in a safe place. It will allow you to benefit from many advantages by registering your product on our website.
For this, go to www.e-zicom.com

References

• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>