TECKTOO 3CCT Led Under Cabinet Lights Plug-in User Manual
- June 16, 2024
- TECKTOO
Table of Contents
18IN LED WORK BENCH LIGHT
-3CCT
Package Contents
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | 18 Inch LED Work Bench Light w/attached 5ft Power Cord | 1 |
| B | Mounting Screw | 2 |
| C | Drywall Anchors | |
| D | Iron Plate with 3M Adhesive | 2 |
Note: Hardware not shown to actual size.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WARNING: These products may represent a possible shock or fire hazard if
improperly installed or at tached in any way. Products should be installed in
accordance with these instructions, current electrical codes, and/or the
current National Electric Code (NEC). Disconnect power to the unit prior to
installation.
WARNING: To reduce risk of fire, electric shock, or injury to persons, be sure
that power supply is turned off at fuse box or circuit breaker before
attempting installation or servicing of the fixture.
WARNING: Injury to persons and damage to the fixture and/or mounting surface
may result if the fixture is pulled from the surface. To reduce the likelihood
of such injury or damage, mount to a surface that is mechanically sound.
SAVE THESE INSTRUCTIONS. For safest operation, read and become familiar with
complete installation instructions prior to use. Pay close attention to this
manual and stay within its guidelines when using this product.
ADDITIONAL SAFETY MEASURES
- To avoid electrical shock, do not turn on fixture with missing or damaged lens.
- There are no serviceable parts inside LED module.
- LEDs emit bright light. Avoid looking directly at the light source.
- If power cord is used, do not alter it in any way.
- Do not install the strip lighting near flammable liquids.
- Do not use with any other cord, cable or connector other than those provided with the fixture or recommended in this instruction manual.
- Keep fixtures away from curtains and other combustible materials.
- This portable luminaire has a polarized plug (one blade is wider than the other) to reduce the risk of electric shock. This plug will fit in a polarized outlet one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter plug.
- Suitable for indoor dry locations only.
SAVE THESE INSTRUCTIONS
MAGNETS
WARNING: RISK OF FALLING. This fixture has built-in magnets disks (Fig.
A) which can be attached to ferrous surfaces that contain iron (FERROUS) in
them like steel. Metals like brass, copper, zinc, and aluminum ARE NOT
magnetic, therefore, it will not hold the fixture properly and can fall
causing damage to the unit, surrounding property, and could result in serious
injury or death to the user or other living objects if not attached correctly
using the supplied screws. ALWAYS use the supplied screws for a more secure
and permanent installation.
Magnets are only meant to be used for non-permanent, quick-fix use, where
light is needed for a short period.
PREPARATION
Before beginning assembly, installation, or operation of product, make sure
all parts are present. Compare parts with package and hardware contents lists
on page 1. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement
parts.
Tools Required for Assembly (not included): Pencil, Phillips Screwdriver or
Electric Drill, Safety Glasses Estimated assembly time: 20 minutes
INSTALLATION INSTRUCTIONS
-
Determine the desired location of the light fixture (A).
Using a pencil, mark the locations of the mounting holes onto the mounting surface. Ensure the power input side of the fixture (A) is no more than 5 feet from a 120V power receptacle. -
Use an electric drill (or start holes with an awl) and screw in the mounting screws (B) into the mounting surface at the locations marked during Step 1. Be sure to leave approximately 1/4″ of the screw exposed to fit in the fixture’s mounting hole slots.
-
Using the heads of the two screws (B) installed during Step 2 as a guide, bring the light fixture (A) to the surface so that the keyholes slip over the screws (B), then slide the light fixture so the screw heads rest over the narrow part of the keyhole slot.
-
Insert the attached power cord into an appropriate 120V AC receptacle.
-
Subsequent fixtures can be installed so they are powered from an adjacent fixture by using the 120V receptacle on the face of the fixture. Plug the power cable from additional fixtures into the 120V receptacle, being sure the connection is secure.
NOTE: Maximum number of adjacent units that can be inter-connected is 10. Installation on the wood with Iron plate -
Tear off the release paper from the adhesive on D.
Place the Iron plate on the surface, and the size is 12inchs between the two irons.Then place the fixtrue on the iron.
Reference step 4,5,6 for next. -
For Fixture operation:
CCT Switch: Use the CCT switch to select light color temperature from 3000K, 4000K or 5000K.
ON/OFF Switch: Use the ON/OFF switch to control the 120V receptacle (outlet).
Main Light Switch: There are three settings. Use the switch to toggle bettween High – Off – Low.
USB Charging Ports: There are 2 USB charging ports on the fixture face. Use these ports to charge other electronics that utilize USB charging.
CARE AND MAINTENANCE
- Do not use if there is any damage to the light or power cord insulation. Inspect periodically.
- Wash hands after use.
- Do not use chemical solvents or harsh abrasives to clean fixture. Use a dry soft cloth to clean if needed.
TROUBLESHOOTING
- The light does not come on at all:
a) Make sure fixture is plugged in.
b) Make sure the wall switch and circuit breaker are on.
If unable to fix any of the above issues, please contact us at support@tecktoo.com,
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>