mxion aerolightCompact User Manual
- June 3, 2024
- mXion
Table of Contents
mxion aerolightCompact
Introduction
Dear customer, we strongly recommend that you read these manuals and the
warning notes thoroughly before installing and operating your device. The
device is not a toy (15+).
NOTE: Make sure that the outputs are set to the appropriate value before
hooking up any other device. We can’t be responsible For any damage if this is
disregarded.
General information
We recommend studying this manual thoroughly before installing and operating
your new device.
NOTE: Some funktions are only available with the latest firmware. Please make
sure that your device is programmed with the latest firmware.
Summary of Funktions
24 High-Power-RGB-LEDs integrated Ideally to implement into lamps (e.g. GRÖNÖ)
- Smooth-Shift all colors
- Colors available individually Automatic dimming
- Sleep-Timer configurable
- WLAN compatible
- Iterates 19 colors in Smooth-Mode Status-LED
- Colors clock set to 5min. up to 1h
- 20 colors available individually (WLAN) 3 colors manuell configurable
- Hand sensor can switch on/off Colourmanagment over the mouse pointer
Color transfer via LightPilot®-APP
Times can be changed, memory effect Storing the last state even after power failure
Scope of supply
- Manual
- Trafo 12V/2A aerolightCompact
Hook-Up
Install your device in compliance with the connecting diagrams in this manual.
The device is protected against shorts and excessive loads. However, in case
of a connection error e.g. a short this safety feature can’t work and the
device will be destroyed subsequently.
Make sure that there is no short circuit caused by the mounting screws or
metal.
NOTE: When starting the aerolite flash the lights. It connects to the
time to the WLAN, and then pick up necessary data. This process takes about 5
sek. Then you can use the aerolite actively use. Send during no data operation
on the device.
FIRST START: Wait for the process up from flashing. Then you can use the
login device on your network (procedure see app/MDTerm).
Product Description
The aerolightCompact is the perfect device to use it in many commercially
available lamps retrofit and install. Some examples are the IKEA® lamps (e.g.
IKEA® GRÖNÖ). Also the installation in other lamp systems or for illumination
of various objects is very easily possible. After a power failure of the
device, we last saved state. Have you, e.g. in Smooth Mode, the device begins
to power automatically with the Smooth Mode on.
About SmartTerm
the color located at the mouse pointer may appear be, for this purpose you
need to activate the color picker. To control the color in the top right
corner displayed. If you paint a particulary good likem you can via keyboard
shortcuts save and then again at any time. The brightness can be adjusted by
plus slider. With the LightPilot-App you can bonus colors configure and save
and call. This can be various other colors select and there may even colors of
your own images are used. Even, you can do everything else with this app,
slide through this. It is controlled via app „LightPilot“.
WLAN facility
PC: To set your device:
- Click on switch „Einstellungen“ from SmartTerm and click now on „Im Netzwerk anmelden“. Follow the instructions on screen.
ANDROID®: How to set up your device:
- After start App LightPilot, the correct screen will open. Follow instructions.
- Optionally, slide left to 2nd screen. Click to „Network“ an follow the instructions.
Technical data
Power supply:
- 10 – 15 V DC
Power:
- 24W (max. power supply)
- Standby <0.5W
Temperature range:
- -20 up to 80°C
Dimensions LBH (cm):
- 7.27.22.5
NOTE: In case you intend to utilize this device below freezing temperatures, make sure it was stored in a heated environment before operation to prevent the generation of condensed water. During operation is sufficient to prevent condensed water.
Warranty, Service, and Support
micron-dynamics warrants this product against defects in materials and workmanship for one year from the original date of purchase. Other countries might have different legal warranty situations. Normal wear and tear, consumer modifications as well as improper use or installation are not covered. Peripheral component damage is not covered by this warranty. Valid warrants claims will be serviced without charge within the warranty period. For warranty service please return the product to the manufacturer. Return shipping charges are not covered by micron-dynamics. Please include your proof of purchase with the returned goods. Please check our website for up-to-date brochures, product information, documentation and software updates. Software updates you can do with our updater or you can send us the product, we update for you free. Errors and changes excepted.
Hotline
For technical support and schematics for application examples contact:
micron-dynamics
info@micron-dynamics.de
service@micron-dynamics.de
www.micron-dynamics.de
https://www.youtube.com/@micron-dynamics