ANANDA S15 Torque Sensor User Manual

June 27, 2024
ANANDA

ANANDA S15 Torque Sensor User Manual

Preface

This document specifies the technical specifications for the product listed.
This document specifies the requirements on functions, conditions of use, reliability, materials and etc. of the product listed.
The Product is designed and produced for the markets in the EU, the U. S., and China.
If the Product is to be sold to a country or region other than that, additional approval might be required to ensure the compliance with local regulations and the limits of any intellectual property rights.

Applicable models include:

Torque sensor S15

Special notes:

Any change made to the Technical  Specifications must be  subject to the ANANDA procedure  for document modification as well as re- confirmation by the signatories and approval of the customer.
The clarification and explanation for any clauses herein shall be subject to the instructions of the technical lead of the project.

Revision history:


Version Doc. No./ Content of revision Revised by Date
01 Adding of packaging information and revision of

electrical definitions of interfaces

| Zhu Huixiang| 2022/09/08
02| Modification   of     the    technical                           parameter list according to the meeting minutes| Zhu Huixiang| 2022/09/22
03| Adding of tooth profile parameters of the matching

crankset

| Zhu Huixiang| 2022/ 10/09
04| Update of technical parameters, optimization of left

and right axle cups, and adding of installation instructions

| Zhu Huixiang| 2022/ 10/24
05| Modification of electrical definitions| Zhu Huixiang| 2022/ 11/22
06| Adding of electrical definitions and revision of the parameter list| Zhu Huixiang| 2023/02/28
07| Template modification| Zhu Huixiang| 2023/08/10
08| Modify standard,Add Double signal parameter,

Add Outline dimension ,Correct storage and use temperature

| Zhu Huixiang| 2023/09/22

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference, and
  • This device must accept any interference received, including interference that may cause undesired

General

  • ScopeThe Specification specifies the detailed requirements for functions and materials of the S1 5 torque sensor and provides some other information. All technical requirements specified herein are subject to verification in predefined procedures. The number of samples for testing shall be sufficient to verify the long- term compliance of the product with the Technical Specification.
  • Product functions and applicationsThis product is a power sensor for an electric bicycle, integrating torque and speed measurement. Scope of application: This sensor is used to measure the torque and speed of bicycles and electric vehicles.
  • Normative references
  1. EN15194: 2017 Cycles – Electrically power assisted cycles – EPAC bicycle
  2. ISO 4210 2014 Cycles – Safety requirements for bicycles
  3. GB 17761-2018 Safety technical specification for electric bicycle(China)
  4. GB/T 17-2008 Environmental testing for electric and electronic product(China)
2 Product definitions
2. 1 Product features
a. High precision and linearity;
b. No signal drift
c. Fast dynamic response;
d. Maintenance- free, high interchangeability;
e. Small size (standard bottom bracket);
f. Non-contact, long service life, insensitive to bending and axial motion;
g. Low power consumption, long-term stability;
h. Adjustable assembly size and input/output signal.

Technical parameter requirements

Product Specification

Item

| BBTS 1. 1 Central Axle Torque Sensor
---|---
Input voltage| 4.5~5. 1V
Power input| <0.22W
Torque output analog voltage| 0.75~3.34V
Number of speed signal pulses| 24r
Duty cycle of speed signal| 50%
Slope of sensor signal| 25mV/N ·m
Measurement range| 0~ 100N.m
Design standard| EN14764
Headset thread gauge| BS(C) 1.375X24
Measurement type| Static and dynamic
Crankset specification| General bicycle standard
Protection class| IP66
Salt spray tset| 96H
Operating temperature| -20~55℃
Storage temperature| -20~ 60℃

Speed signal

Power on the central axle torque sensor properly, connect its speed signal wire to the probe of an oscilloscope, and turn the central axle torque sensor by one revolution. The oscilloscope can detect 24 sets of square pulse waves in the signal output of the central axle torque sensor.

Product appearance and size

a ,Outline drawing

Specification L2 L3 L4 L5
L1= 151mm 41.5mm 68mm 41.5mm 45.5mm
L1= 151mm 39mm 73mm 39mm 45.5mm
L1= 165mm 40.5mm 84mm 40.5mm 53.5mm
L1= 181mm 40.5mm 100mm 40.5mm 61.5mm

.Threads and parameters of crankset installation

YY:Year WW:Week XXXX:SN

Packaging requirements

  1. Size of packaging box

L =508mm W=380mm H= 182mm

Quantity: Specification: S15

Specification: S15
Specification: S15

L1= 151
L1= 165
L1= 181
per box per box per box
42pcs 42pcs 30pcs

Note: Components and parts can be packaged separately.

Each carton should be marked with info on: logistics, product, quantity and model; Products are shipped with pallets. The stacking height and number of products on each pallet shall meet the order The length, width and height of each pallet are limited to 1,200mm × 800mm × 1, 100mm.

  1. Packaging materials shall be green, energy- efficient and

Instructions for Use

  1. 1 External conditions:

Excessive mechanical stress ( e. g. longitudinal force/ load exceeding the specified limit, and intense vibration) may cause damage to the sensor and result in poor signal output.

  • Safety measures
  1. Do not remove the sensor housing under any
  2. Note the maximum electrical and mechanical load requirements in sensor
  3. Protect the sensor from exposure to any electromagnetic field that does not conform to electromagnetic compatibility

Installation Diagrams

_ Warning: _The 2. 5 mm washers at both ends of the torque sensor must be installed to avoid axial over-tightness and uneven crank rotation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals