mxion TLD Module User Manual
- June 3, 2024
- mXion
Table of Contents
mxion TLD Module
Introduction
Dear customer, we strongly recommend that you read these manuals and the warning notes thoroughly before installing and operating your device. The device is not a toy (15+).
NOTE: Make sure that the outputs are set to appropriate value before hooking up any other device. We can’t be responsible For any damage if this is disregarded.
General information
We recommend studying this manual thoroughly before installing and operating
your new device.
Place the decoder in a protected location. The unit must not be exposed to
moisture.
NOTE: Some functions are only available with the latest firmware.
Please make sure that your device is programmed with the latest firmware.
Summary of Functions
- DC/AC/DCC operation
- Function output as OE
- Changing switching resistor
- 2 mode usable
- Brightness dimmer
Scope of supply
- Manual
- mXion TLD
- LDR
- 150k Ohm resistor
- 200k Ohm resistor
Hook-Up
Install your device in compliance with the connecting diagrams in this manual.
The device is protected against shorts and excessive loads. However, in case
of a connection error e.g. a short this safety feature can’t work and the
device will be destroyed subsequently.
Make sure that there is no short circuit caused by the mounting screws or
metal.
Connectors on the upper surface
Product description
The mXion TLD is a versatile usable module.
The TLD is a brightness dimmer. Take the A1 function output. The output is 2A
resilient.
There are 2 modes available:
Increases with increasing brightness the voltage at A1 (brighter).
Screw this, the LDR to terminal „R2“, the 200kΩ resistor (red, black, yellow,
gold)„R1“.
Increases with increasing brightness the voltage to A1 from (darker).
Screw this, the LDR to terminal „R1”, the 150kΩ resistor (brown, green,
yellow, gold) with „R2“.
Application examples
The examples shown here serve only to excite.
Some possible examples of the mXion TLD can hereby they example an engine or
lighting dependent the ambient lighting slower or faster, or brighter and
darker.
You may optionally the LDR with a NTC/PTC replace (temperature resistor) so
you could, for example a fan regulate the temperature.
(NTC/PTC is not resistor (150kΩ, 200kΩ) have become redefined.
Technical data
- Power supply: 7-25V DC/DCC (peaks max. 27V) 5-18V AC
- Current: 30-120mA (with out functions)
- Maximum function current: A1 2Amps.
- Temperature range: -20 up to 100°C
- Dimensions LBH (cm): 3.54.52
NOTE: In case you intend to utilize this device below freezing temperatures, make sure it was stored in a heated environment before operation to prevent the generation of condensed water. During operation is sufficient to prevent condensed water.
In terms of the NTC (temperature resistor) you should to the temperature range of the NTC otherwise no proper function can be guaranteed.
Warranty, Service, Support
micron-dynamics warrants this product against defects in materials and workmanship for one year from the original date of purchase. Other countries might have different legal warranty situations. Normal wear and tear, consumer modifications as well as improper use or installation are not covered. Peripheral component damage is not covered by this warranty. Valid warrants claims will be serviced without charge within the warranty period. For warranty service please return the product to the manufacturer. Return shipping charges are not covered by micron-dynamics. Please include your proof of purchase with the returned good. Please check our website for up to date brochures, product information, documentation and software updates. Software updates you can do with our updater or you can send us the product, we update for you free.
Errors and changes excepted.
Hotline
For technical support and schematics for application examples contact:
micron-dynamics
info@micron-dynamics.de
service@micron-dynamics.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>