mxion miniCap User Manual
- June 3, 2024
- mXion
Table of Contents
mxion miniCap
Introduction
Dear customer, we strongly recommend that you read these manuals and the
warning notes thoroughly before installing and operating your device. The
device is not a toy (15+).
NOTE:
Make sure that the outputs are set to appropriate value before hooking up any
other device. We can’t be responsible For any damage if this is disregarded.
General information
We recommend studying this manual thoroughly before installing and operating
your new device. Place the decoder in a protected location. The unit must not
be exposed to moisture.
NOTE:
Some funktions are only available with the latest firmware.
Please make sure that your device is programmed with the latest firmware.
Summary of Functions
The min Cap (Power cap) is used for bridging short-term interruptions at model
railway locomotives or for buffering noises. Motor and decoder will be during
the supplied from the buffer, the locomotive drives with the set speed
continues without going from de-energized pieces to be influenced. The buffer
is also excellent for sound modules in analog mode for the stop session. Also,
can b e used in analog (with decoder). Depending on the state of charge and
load, the buffer 1-2 min. buffert he decoder, and so on bridge larger no-
current areas. Due to the compact design ideal for everyone large trains from
lane 0 to G.
Scope of supply
- Manual
- mXion miniCap
Hook-Up
Install your device in compliance with the connecting diagrams in this manual.
The device is protected against shorts and excessive loads. However, in case
of a connection error e.g. a short this safety feature can’t work and the
device will be destroyed subsequently. Make sure that there is no short
circuit caused by the mounting screws or metal.
Connectors
The buffer can be connected to all popular decoders be connected easy the
connection to our decoder of the DRIVE series as well as our function decoder.
You can the white cable to any output connect and there BC in the special
function activate. For example Buffer at A1 CV123 = 20. For foreign decoders,
remove the setting the respective manual of the manufacturer.
The red wire is connected to DEC+
The green or black wire is connected to DEC-.
With built-in buffer, turn on the decoder CV29 bit 2 = 0, so that the decoder
is the voltage of the buffer does not recognize as analog current. For
decoders without BC options can be a switch between white and black cables are
connected (foreign decoder).
Connection for Decoder with BC:
Connection for Decoder without BC:
Technical data
Power supply:
- 5 – 24V (DC)
Current:
- 300 mA (at 24V track supply)
Maximum output voltage:
- 20 V (fully loaded)
Maximum current output:
- 3 Amps.
Temperature range:
- -20 up to 65°C
Dimensions LBH (cm):
- each 0.72.43
- Rai Community compliant to RCN-530
NOTE:
In case you intend to utilize this device below freezing temperatures, make
sure it was stored in a heated environment before operation to prevent the
generation of condensed water. During operation is sufficient to prevent
condensed water.
Warranty, Service, Support
micron-dynamics warrants this product against defects in materials and
workmanship for one year from the original date of purchase. Other countries
might have different legal warranty situations. Normal wear and tear, consumer
modifications as well as improper use or installation are not covered.
Peripheral component damage is not covered by this warranty. Valid warrants
claims will be serviced without charge within the warranty period. For
warranty service please return the product to the manufacturer. Return
shipping charges are not covered by micron-dynamics. Please include your proof
of purchase with the returned good. Please check our website for up to date
brochures, product information, documentation and software updates. Software
updates you can do with our updater or you can send us the product, we update
for you free.
Hotline
For technical support and schematics for application examples contact:
micron-dynamics
info@micron-dynamics.de
service@micron-dynamics.de
www.micron-dynamics.de
https://www.youtube.com/@micron-dynamics