mxion Programming Module User Manual
- June 3, 2024
- mXion
Table of Contents
mxion Programming Module
Introduction
Dear customer, we strongly recommend that you read these manuals and the
warning notes thoroughly before installing and operating your device.
NOTE: Make sure that the outputs are set to the appropriate value before
hooking up any other device. MD can’t be responsible For any damage if this is
disregarded.
General information
We recommend studying this manual thoroughly before installing and operating
your new device.
NOTE: Some functions are only available with the latest firmware. Please make
sure that your device is programmed with the latest firmware.
Summary of Functions
USB programming module for mXion DCC update for mXion DCC modules XpressNet®
update for mXion XpressNet® Dev DCC CV read/write possible Testing Decoders
(Central function)
CV-Programmer
Can used for Firmware selection of mXion LED connectivity and working LEDs
Power supply for modules integrated Self updateable
Scope of supply
- Manual
- programming module
- USB cable
- 15V/1A Supply
- Programming adapter for mXion devices
Hook-Up
Install your device in compliance with the connecting diagrams in this manual.
The device is protected against shorts and excessive loads. However, in case
of a connection error e.g. a short this safety feature can’t work and the
device will be destroyed subsequently. Make sure that there is no short
circuit caused by the mounting screws or metal.
Connectors
Spannungsversorgung (15V, max. 0.5A) für Updategerät
- Voltage (15V, max. 0.5A) for update device
DCC-Update Anschluss (Programmiergleis)
- DCC update connector (programming track)
DCC/MM Programmiergleis
- DCC/MM Programming track
Product Description
Programming adapter for the is software updates for all mXion products suitable. Through the supplied cable update the devices. Plug this cable into the 3 holes on the board. This allows you to update most devices. The devices are over it with the tension provided. Optionally you can choose from the two screw terminals 15V supply voltage relate. For devices with XpressNet® support please use the XpressNet® for this for the update via XpressNet® Some devices can be controlled DCC (digital) be updated (e.g. mXion DRIVE). Connect the device tot he two screw terminals. These then form a programming track like one digital center. You can over here also read and writing CVs is possible. the programmer will also be used to use for read/write CVs, so as a CV programmer with a programming track. The programmer done with our mXionTool and is very easy. The connection to the terminal is automatic, as also the recognition of the programmer. Then you can read CVs, write program registers and much more. It is also possible to use bits show and long calculate points. Such as locomotive addresses. The terminal is constantly being expanded, too the software of the programmer always more features and facilitated ensure programming too can. MD decoders can work with one button pressure detected and identifed become. The following pictures show the procedure with ours moonpool (12/2019). The implementation for templates are still not available yet. Here can you load XML templates directly in the future?
Furthermore, there is the possibility that one can test programmed values immediately. They have with the mXionTool the pos. to decoder completely to test. This turns the programmer in a mini-control center, with all functions/decoders can test. Turnouts can also be permanent back/forth (toggle test). Also the Roco mode is supported. For driving steps are selected and tested. The area SUSI is not available for the central station but refers to our CV Programmer the article number 0024. The software fits automatically to the respective hardware.
Warranty, Service, Support
micron-dynamics warrants this product against defects in materials and workmanship for one year from the original date of purchase. Other countries might have different legal warranty situations. Normal wear and tear, consumer modifications as well as improper use or installation are not covered. Peripheral component damage is not covered by this warranty. Valid warrants claims will be serviced without charge within the warranty period. For warranty service please return the product to the manufacturer. Return shipping charges are not covered by micron-dynamics. Please include your proof of purchase with the returned good. Please check our website for up to date brochures, product information, documentation and software updates. Software updates you can do with our updater or you can send us the product, we update for you free. Errors and changes excepted.
Hotline
For technical support and schematics for application examples contact:
micron-dynamics
info@micron-dynamics.de
service@micron-dynamics.de
www.micron-dynamics.de
https://www.youtube.com/@micron-dynamics
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>