Beldray EEF220401 2-in-1 Cordless Pro Vacuum Cleaner Instruction Manual
- June 4, 2024
- Beldray
Table of Contents
Our cordless, powerful & versatile vacuum cleaner
2 IN 1
CORDLESS PRO
INSTRUCTION MANUAL
www.beldray.com
Please retain instructions for future reference.
Safety Instructions
When using electrical appliances, basic safety precautions should always be
followed.
Check that the voltage indicated on the rating plate corresponds with that of
the local network before connecting the appliance to the main power supply.
Children aged from 8 years and people with reduced physical, sensory or mental
capabilities or lack of experience and knowledge can use this appliance, only
if they have been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children should be supervised to ensure that they do not play with the
appliance.
Unless they are older than 8 and supervised, children should not perform
cleaning or user maintenance.
If the power supply cord, plug, or any part of the appliance is malfunctioning
or if it has been dropped or damaged, cease using the product immediately to
avoid potential injury.
This appliance contains no user-serviceable parts, only a qualified
electrician should carry out repairs.
Improper repairs may place the user at risk of harm.
Do not remove the adaptor from the mains power supply by pulling the cord;
switch off and remove the plug by hand.
Do not use the adaptor to recharge non-rechargeable batteries or any other
appliance.
Do not use the appliance for anything other than its intended use. Take care
when equipping accessories with rotating parts as this could cause entrapment.
Switch off the appliance, disconnect it from the mains power supply and allow
it to cool fully before changing or fitting accessories and before cleaning or
user maintenance.
Use of an extension cord with the appliance is not recommended. Only use the
appliance with the power supply unit provided. This appliance should not be
operated by means of an external timer or separate remote control system. This
appliance is intended for domestic use only. It should not be used for
commercial purposes.
CAUTION: The extension tube contains electrical connections. Do not use
it to suck up water. Do not immerse in water for cleaning. The extension tube
should be checked regularly and must not be used if damaged.
Battery Safety
The supply terminals are not to be short-circuited.
In the event of a battery pack leaking, do not allow the liquid to come in
contact with the skin or eyes. If contact has been made, wash the affected
area with copious amounts of water and seek medical advice.
Secondary cells and batteries need to be charged before use.
After extended periods of storage, it may be necessary to charge and discharge
the battery pack several times to obtain maximum performance.
Do not leave a battery pack on prolonged charge when not in use.
Do not use any charger other than that specifically provided for use with the
product.
Do not use any cell or battery which is not designed for use with the product.
Keep batteries out of the reach of children.
Do not crush, puncture, dismantle or otherwise damage battery packs.
Do not store above 60 °C.
Avoid storage in direct sunlight.
Do not expose battery packs to heat or fire as they may explode.
Do not subject battery packs to mechanical shock. Do not dispose of exhausted
battery packs in household waste. To dispose of the exhausted battery pack,
take it to a local recycling station. Contact the local government offices for
further details. This product is fitted with a 22.2 V 2200 mAh Li-ion
rechargeable battery.
Dos and Don’ts
DO:
Charge the vacuum cleaner fully before use.
Check that the HEPA filter is kept clear of obstruction.
Make sure that the dust container and HEPA filter are cleaned regularly to
preserve suction and prolong the life of the vacuum cleaner.
Clean the dust container and HEPA filter at least every two weeks with clean
water to keep the vacuum cleaner working efficiently.
Don’t:
Use the vacuum cleaner without the HEPA filter or dust container in position.
Use the vacuum cleaner to pick up flammable liquid, matches, cigarette ends,
hot ashes, or any hot, burning, or smoking objects. Use the vacuum cleaner to
pick up water or any other liquid, as this poses a risk of an electric shock.
Care and Maintenance
Wipe the external surface of the vacuum cleaner with a soft, damp cloth and
allow it to dry thoroughly.
Do not use any harsh or abrasive detergents or cleaning agents to clean any
part of the vacuum cleaner.
Keep the HEPA filter clean and replace it when it becomes worn.
Description of Parts
1. | 2 in 1 Cordless Pro main unit | 11. | Dust container |
---|---|---|---|
2. | Air inlet | 12. | Dust container base release latch |
3. | Extension tube | 13. | Filter cone |
4. | Extension tube release button | 14. | NEPA filter |
5. | Floor brush | 15. | Battery pack |
6. | Floor brush release button | 16. | Battery release catch |
7. | Brush bar | 17. | Charging port |
8. | Brush bar release tab | 18. | LED indicator light |
- 10.| 2 in 1 crevice and brush tool
Power trigger| 19.| Storage hook
Instructions for Use
Before First Use
Before using the vacuum cleaner for the first time, clean the exterior surface
with a soft, damp cloth and dry thoroughly. Do not immerse the vacuum cleaner
in water or any other liquid.
Charging the 2 in-1 Cordless Pro
Before first use, the vacuum cleaner must be charged for approx. 5 hours.
Subsequent charging times will vary depending upon use. If the vacuum cleaner
battery becomes drained completely during use, it may take up to 5 hours to
fully recharge.
The battery pack must be fitted onto the vacuum cleaner main unit during
charging; do not charge the battery pack separately.
STEP 1: Before connecting to the mains power supply, attach the battery
pack by aligning it with the main unit and sliding it into place until it
clicks.
STEP 2: Connect the mains power adaptor to the charging port on the
battery pack.
STEP 3: Plug the mains power adaptor into the mains power supply; the LED
indicator light will flash during charging and then remain illuminated once
the battery is fully charged.
STEP 4 : Unplug the mains power adaptor from the mains power supply once
the battery is fully charged. Disconnect the mains power adaptor from the
charging port on the battery pack.
NOTE: Whilst charging, the battery pack may become warm.
WARNING: Do not use any mains power adaptor other than that supplied.
Using an alternative will increase the risk of damage to the appliance or
injury to the user.
Using the 2 in-1 Cordless Pro
STEP 1: Check that the vacuum cleaner is disconnected from the mains
power adaptor after unplugging it from the mains power supply. Make sure the
battery pack is securely attached to the main unit.
STEP 2 : Turn on the vacuum cleaner by pressing the power trigger; press
once for the minimum power setting, and press twice to use the maximum power
setting.
STEP 3: To turn off the vacuum cleaner, press the power trigger.
WARNING: Do not use the vacuum cleaner without the HEPA filter and filter
cone in position. The dust container must be closed before use. Clean the HEPA
filter regularly to preserve the suction of the vacuum cleaner.
Using the Extension Tube and Floor Brush
The extension tube can be fitted onto the air inlet to extend reach, ideal for
floor-to-ceiling cleaning.
STEP 1: Fit the extension tube onto the air inlet by aligning the pins
and carefully pushing the extension tube towards the main unit until it clicks
into position. To release the extension tube, press the extension tube release
button and pull it away from the vacuum cleaner main unit.
STEP 2: Attach the floor brush by aligning the pins on the floor brush
with the bottom of the extension tube. Carefully push together to secure into
place. To release the floor brush, press the floor brush release button and
pull it away from the extension tube.
STEP 3: Turn on the vacuum cleaner by pressing the power trigger.
Using the 2 in-1 Crevice and Brush Tool
STEP 1: If required, fit the extension tube onto the air inlet following
the instructions in the section entitled ‘Using the Extension Tube and Floor
Brush’.
STEP 2: Push the 2-in-1 crevice and brush tool onto the end of the
extension tube. If no extension is required, push the crevice tool directly
onto the air inlet until secure. STEP 3: Slide the brush bar back to use
as a crevice tool, ideal for removing dust and dirt from corners and recesses.
Slide the brush bar forward to use as a brush tool, perfect for cleaning
upholstery and fabrics.
STEP 4: To remove the 2-in-1 crevice and brush tool, pull it firmly away
from the end of the extension tube or the air inlet.
Emptying the Dust Container
Before emptying the dust container, check that the vacuum cleaner is switched
off and any attachments have been removed from the air inlet. It is
recommended to empty the dust container outdoors.
STEP 1 : Whilst securely holding the vacuum cleaner main unit, press the
cust container base release latch. Empty the dust container slowly and
carefully to reduce the amount of dust released back into the atmosphere.
STEP 2 : Close the dust container by pushing the base closed until the
dust container base release latch locks back into position.
NOTE: Always close the dust container base before using the vacuum
cleaner.
Cleaning the HEPA filter
The HEPA filter can only be accessed when the dust container is open.
STEP 1: Open and empty the dust container following the instructions in
the section entitled ‘Emptying the Dust Container.
STEP 2: Once the dust container is empty, remove the filter cone by
rotating it in an anticlockwise direction and lifting it out of the vacuum
cleaner main unit.
STEP 3 : Carefully lift the HEPA filter out of the dust container. Shake
the HEPA filter until the majority of the dust has been removed, then rinse
under clean, warm water and allow it to dry naturally.
STEP 4: Once the HEPA filter is fully dry, place it back into the dust
container. Replace the filter cone by aligning the indents on the filter cone
with those on the top of the HEPA filter. Secure into place by rotating the
filter cone in a clockwise direction.
STEP 5 : Close the dust container by pushing it firmly shut until it
clicks into position.
NOTE: Do not clean the HEPA filter using detergents or use external heat
sources such as radiators to dry them.
WARNING: Do not reassemble or use the vacuum cleaner until the HEPA
filter is fully dry, as this could cause damage.
Cleaning the Floor Brush
The floor brush has a removable brush bar for easy cleaning.
STEP 1: Switch off the vacuum cleaner and remove the floor brush by
pressing the floor brush release button and pulling it away from the extension
tube.
STEP 2: Slide the brush bar release tab to release the brush bar and lift
it out of the floor brush.
STEP 3: Remove any built-up dust, debris, and hair from the brush bar and
floor brush.
STEP 4: Replace the brush bar with the floor brush by aligning the tabs
and sliding the brush bar release tab to the side, allowing the brush bar to
fit into place.
Removing the Rechargeable Battery Pack
The battery pack can be removed from the vacuum cleaner main unit by pressing
the battery release catch and sliding the battery pack out of the main unit.
To refit the battery pack, re-align it with the main unit and press the
release catch down whilst sliding the battery pack into place until it clicks.
Storage
Check that the vacuum cleaner is cool, clean, and dry before storing it in a
cool, dry place. The vacuum cleaner can be neatly stored away after use by
securing the main unit onto the extension tube using the storage hook.
Symptom | Possible Cause | Solution |
---|---|---|
The vacuum cleaner will not charge. | The mains power adaptor is not securely |
connected.
The battery is not secured properly.| Connect the mains power adaptor to the
charging port on the main unit, following the instructions in the section
entitled ‘Charging the 2 in 1 Cordless Pro’.
Check that the battery pack is secured onto the unit.
His suction is poor.| The air inlet is blocked.
The dust container is almost full.
The HEPA filter is blocked.| Disconnect the attachment and clear the blockage.
Empty the dust container following the instructions in the section entitled
‘Emptying the Dust Container.
Clean the HEPA filter following the instructions in the section entitled
‘Cleaning the HEPA filter’.
His brush bar is riot rotating.| The brush bar is blocked due to built-up
hair, dust, and debris.| Clean the floor brush following the instructions in
the section entitled ‘Cleaning the Floor Brush’.
Specifications
Product code: BEL01469LDL
Battery: 22.2 V DC 2200 mAh Li-ion
Adaptor Input: 100-240 V – 50/60 Hz
Adaptor Output: 26 V ****0.4 A 10.4 W
Average active efficiency: 83.81 %
Efficiency at low load (10 %): 75.78 %
No-load power consumption: 0.01 W Dust tank capacity: 1.2 L
Rechargeable batteries are not included in the extended manufacturer’s guarantee (after the first 12 months).
UP Global Sourcing UK Ltd.,
The UK. Manchester OL9 ODD.
Germany. 51149 Köln.
If this product does not reach you in an acceptable condition please contact
our Customer Services Department at www.beldray.com
Please have your delivery note to hand as details from it will be required.
If you wish to return this product please return it to the retailer from where
it was purchased with your receipt (subject to their terms and conditions).
Guarantee
All products purchased as new carry a manufacturer’s guarantee; the time
period of the guarantee will vary dependent upon the product. Where reasonable
proof of purchase can be provided, Beldray will provide a standard 12-month
guarantee with the retailer from the date of purchase. This is only applicable
when products have been used as instructed for their intended, domestic use.
Any misuse or dismantling of products will invalidate any guarantee.
Under the guarantee, we undertake to repair or replace free of any charge any
parts found to be defective. In the event that we cannot provide an exact
replacement, a similar product will be offered or the cost refunded. Any
damages from daily wear and tear are not covered by this guarantee, nor are
consumables such as plugs, fuses, etc.
Please note that the above terms and conditions may be updated from time to
time and we, therefore, recommend that you check these each time you revisit
the website.
Nothing in this guarantee or in the instructions relating to this product
excludes, restricts, or otherwise affects your statutory rights.
Disposal of Waste Batteries and Electrical and Electronic Equipment
This symbol on the product, its batteries, or its packaging means that this
product and any batteries it contains must not be disposed of with household
waste. Instead, it is the user’s responsibility to hand this over to an
applicable collection point for the recycling of batteries and electrical and
electronic equipment. This separate collection and recycling will help to
conserve natural resources and prevent potential negative consequences for
human health and the environment due to the possible presence of hazardous
substances in batteries and electrical and electronic equipment, which could
be caused by inappropriate disposal. Some retailers provide take-back services
which allow the user to return exhausted equipment for appropriate disposal.
It is the user’s responsibility to delete any data on electrical and
electronic equipment prior to disposal. For more information about where to
drop batteries, and electrical and electronic waste off, please contact the
local city/municipality office, household waste disposal service, or the
retailer.
*To be eligible for the extended guarantee, go to guarantee.upgs.com/beldray
and register your product within 30 days of purchase.
www.facebook.com/Beldray
Find us on ****
Manufactured by:
UP Global Sourcing UK Ltd.,
The UK. Manchester OL9 ODD. Germany.
51149 Köln.
www.beldray.com
©Beldray Trademark.
All rights reserved.
CD090418/MD250422N5
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>