Beldray BEL0987 2 in 1 Cordless Steam Iron User Guide
- June 5, 2024
- Beldray
Table of Contents
TWO-IN-ONE
CORDLESS 360 °
QUICK START GUIDE
Find us on
www.facebook.com/Beldray
Please read all of the instructions carefully and retain them for future reference.
Safety Instructions
When using electrical appliances, basic safety precautions should always be
followed. Check that the voltage indicated on the rating plate corresponds
with that of the local network before connecting the appliance to the main
power supply. Children aged from 8 years and people with reduced physical,
sensory or mental capabilities or lack of experience and knowledge can use
this appliance, only if they have been given supervision or instruction
concerning the use of the appliance in a safe way and understand the hazards
involved. Children should be supervised to ensure that they do not play with
the appliance. Unless they are older than 8 and supervised, children should
not perform cleaning or user maintenance.
This appliance contains no user-serviceable parts. If the power supply cord,
plug, or any part of the appliance is malfunctioning, if there is any leakage
or if it has been dropped or damaged, do not use it. Only a qualified
electrician should carry out repairs. Improper repairs may place the user at
risk of harm.
Do not leave the appliance unattended whilst connected to the main power
supply.
Do not use the appliance for anything other than its intended use. Do not
direct steam at people or animals or towards equipment containing electrical
components, such as the interior of ovens. Switch off the appliance and
disconnect it from the mains power supply before changing or fitting any
accessories.
Always unplug the appliance after use and allow it to cool fully before any
cleaning or user maintenance.
This appliance must only be used and rested on a stable surface.
This appliance must only be used with the base provided.
This appliance should not be operated by means of an external timer or
separate remote control system.
This appliance is intended for domestic use only. It should not be used for
commercial purposes.
Caution: The appliance emits very hot steam; always exercise extreme
caution during use.
** Hot surface – do not touch the hot section or heating components of the
appliance.
Warning:** Danger of scalding. Keep the appliance away from [flammable
materials.
Care and Maintenance
STEP 1: Drain the remaining water from the water tank to prevent it from
leaking during cleaning.
STEP 2: Wipe the ceramic soleplate with a soft, damp cloth and dry
thoroughly.
STEP 3: If polyester has burnt onto the ceramic soleplate, wipe it with a
soft cloth dipped in methylated spirits. Clean off the methylated spirits with
a soft, damp cloth and dry thoroughly.
STEP 4: To remove any build-up around the steam holes, use a cotton wool
tip dampened with methylated spirits. Wipe off the methylated and dry
thoroughly.
Caution: Do not fill the water tank past the max. fill mark; it is best
to check the water level when the iron is positioned upright.
Do not fill the water tank when the iron is switched on.
Warning: Never add descaling, aromatic, alcoholic, or detergent products
to the water tank, as this could cause damage to the iron or injury to the
user.
Description of Parts
1. | Two-in-one Cordless 360 | 9. | Water tank cap |
---|---|---|---|
2. | Temperature control dial | 10. | Max. fill mark |
3. | Temperature indicator light | 11. | Easy-grip handles 12. Ceramic soleplate |
4. | Steam control/ self-clean switch | 13. | Cord guard |
5. | Steam burst button | 14. | Heel rest |
6. | Water spray button | 15. | Iron base with cord |
7. | Spray nozzle | 16. | Power indicator light |
8. | Water tank | 17. | Locking switch |
18. | Measuring jug |
Instructions for Use
Before First Use
STEP 1: Switch off and unplug the iron from the main power supply.
STEP 2: Wipe the exterior surface of the iron with a soft, damp cloth and
dry thoroughly.
STEP 3: To remove any impurities that may have occurred during the
manufacturing process, it is best to use the iron on an old piece of cloth,
making sure that it is on the highest temperature setting suitable for the
material.
Note: When using the iron for the first time, a slight odor and a small
amount of smoke may be emitted. This is normal and will soon subside.
Allow for sufficient ventilation around the I iron when it is in use.
Using as a Cordless Iron
STEP 1: Move the locking switch right to the cordless position. This will
unlock the iron from the iron base.
STEP 2: Plugin and switch on the iron at the mains power supply; the
power indicator light will illuminate blue to indicate the power unit is on.
This does not indicate that the iron is heating up.
STEP 3: Rotate the temperature control dial to the desired temperature
(1-dot position minimum). The temperature indicator light will illuminate red
to signal that the iron is heating up.
STEP 4: When the temperature indicator light switches off after approx.
25 seconds, remove the iron from the iron base and use as a cordless iron.
STEP 5: Put the iron back onto the iron base to recharge. This will need
to be done regularly in order for the iron to maintain heat. Recharge time is
approx. 5 seconds.
Using as a Corded Iron
STEP 1: When the iron is on the iron base, move the locking switch to
the ‘locked’ position. This will lock the power unit to the iron.
STEP 2: Plugin and switch on the iron at the main power supply.
STEP 3: Rotate the temperature control dial to the desired temperature
(1-dot position minimum).
Ironing with Steam
The steam settings are ideal for removing creases from fabrics such as
cotton and linen with ease.
STEP 1: Fill the water tank.
STEP 2: Plugin and switch on the iron.
STEP 3: Rotate the temperature control dial until the desired heat
setting is reached.
The iron will only produce steam when the temperature control dial is set to
the 3-dot heat setting.
STEP 4: Select the desired steam setting by sliding the steam control
switch to the right. The first click is the lowest steam setting whilst the
last click delivers the highest steam setting. The steam setting can be
switched off at any time by sliding the steam control switch to the off
position.
STEP 5: After use, rotate the temperature control dial to the ‘Off’
position. Switch off and unplug the iron from the mains power supply and allow
it to cool thoroughly.
Note: Allow the iron to reach the desired heat setting before use; not
doing so may cause water to drip from the ceramic soleplate.
The temperature indicator light will cycle on and off during use to regulate
the temperature.
Warning: Never leave the iron’s ceramic soleplate resting on the fabric
for any longer than 15 seconds.
If ironing with steam for prolonged periods of time, it is advisable to use
the iron as a corded unit.
For removing creases from more sensitive fabrics, try ironing without steam.
Ironing without Steam
STEP 1: Move the steam control switch to the off position.
STEP 2: Plugin and switch on the iron.
STEP 3: Rotate the temperature control dial until the desired heat
setting is selected.
STEP 4: Test the iron on a small area of the fabric to check that the
selected temperature is suitable; adjust if necessary.
Steam Burst Function
For creases that are stubborn and difficult to remove, use the steam
control trigger to select the desired steam setting; if necessary, press the
steam burst button for extra steam. Wait approx. 5 seconds in-between each
burst to prevent any water from leaking out from the steam holes.
Water Spray Function
The water spray function can be used to help to remove stubborn creases on
heavier fabrics. It can also be used when dry ironing delicate fabrics that
cannot be steam-ironed.
To use the water spray function, hold the iron over the area to be ironed and
then press the water spray button.
Note: When using the water spray function for the first time, it may be
necessary to press the water spray button several times.
Self-clean Function
The self-clean function removes limescale and impurities from within the
ceramic soleplate.
It is recommended to use this function on a fortnightly basis or more often if
the iron is used in a hard water area.
For further details please see the online instruction manual at
www.beldray.com .
Storage
Check that the iron is cool and dry and that the water tank is empty before
storing it in a cool, dry place.
Wrap the cord loosely around the iron; never wrap it tightly as this could
cause damage.
Specifications
Product code: BEL0987
Input: 220-240 V – 50/60 Hz Output: 2600 W
Water tank capacity: 300 ml
If this product does not reach you in an acceptable condition please contact our Customer Services Department at www.beldray.com . Please have your delivery note to hand as details from it will be required. If you wish to return this product, please return it to the retailer from where it was purchased with your receipt (subject to their terms and conditions).
Go to www.beldray.com/manuals.html
and search BEL0987 to access the instruction manual for your product.
*To be eligible for the extended guarantee, go to www.beldray.com/guarantee-registration.html and register your product within 30 days of purchase.
The crossed-out wheelie bin symbol on this item indicates that this appliance
needs to be disposed of in an environmentally friendly way when it becomes of
no further use or has worn out. Contact your local authority for details of
where to take the item for recycling.
FULL INSTRUCTION MANUAL AT
www.beldray.com/manuals.html
PRODUCT CODE: BEL0987
Manchester
OL9 ODD
United Kingdom
www.upgs.com
T: +44 (0) 161 627 1400 f:
F: +44 (0) 161 628 2126
hk: +852 6681 9752
cn: +86 1 3417586804
Artworker: Ellie Drinkwater
Date: 01/06/2020
Project Name: EES200286 UPG 6EL0987 QSG
Type of Artwork: Quick Start Guide
Size: A4 Folding Leaflet Double-sided
Software Used: Indesign CC20
Typefaces: TW Cen MT
Artwork Version 1
Artwork Scale 1:1
D2020 UP Global Sourcing. All designs, images, and artwork are the copyright
of UP Global Sourcing. No copying, alterations, or amendments to the artwork
design can be undertaken without prior written permission of UP Global
Sourcing. Any costs incurred as a result of unauthorized amendments will be
recovered from the supplier responsible.
Manufactured by:
UP Global Sourcing UK Ltd.,
The UK. Manchester OL9 ODD.
Germany. 51149 Köln. MADE IN CHINA.
www.beldray.com
CO290520/MD000000/V1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>