Kjell 24017 Full HD Projector User Manual

Kjell 24017 Full HD Projector

Overview

1. Lens
2. IR receiver, front
3. VGA port
4. 3.5 mm jack
5. HDMI ports
6. AV port
7. USB ports
8. IR receiver, back
9. Dust filter
10. Power port
11. Power switch
12. Riser
13. Rubber pads and screw holes
14. Dust cover
15. Focus16. Source button
16. Source button
17. Previous button
18. OK button
19. Menu button
20. Power button
21. Indicator
22. Arrow buttons

Remote control

Specifications

Included

Projector, remote control.

Installation

The projector can be mounted on a projector mount in the ceiling or placed on a table or stand. Keep in mind that the projector needs to be at a height where the lens is perpendicular to the screen. If it is not possible, you can adjust the projection using the keystone correction (see page 6).

Installation methods

The projector can be placed in the following locations:

Ceiling

Use a suitable projector mount. Remove the rubber pads (13) underneath the projector to expose the screw holes. Use M4 screws for mounting.

Table

Place the projector on a stable surface and in a height where the lens is perpendicular to the screen.

Use

1. Connect the power cable to the power port (1 D) and a wall outlet.
2. Turn the Power switch (11) to On and press the Power button (20) on the projector or the remote control to turn the projector on.
3. Connect your video source to the projector. You can use either a HDMI, VGA or AV cable. If you want to use an external speaker, connect it to the projector with a 3.5 mm cable.
4. Press the Source button (16) on the projector or remote control to set the input source.
5. Enter the settings menu to set a language in which to display the menu.

Focus adjustments

Turn the focus ring (15) or lens (1) slowly to adjust the focus and get a clear image. If the image is still blurry, try to move the projector further away from the screen.

Settings

Press the Home button( ) on the remote control to enter the projector’s homepage. Navigate to the settings ( ) in the upper right corner and press OK to enter the settings menu.

Use the Arrow buttons (22,▲▼◄►) to navigate through the menus. Press the OK button (18) to enter submenus and to confirm your options. You can use either the remote control or the buttons on the projector.

Input source

Choose the input source on the homepage or press the Source button (16) on the projector or the remote control. Select the same source as the corresponding cable you have connected your video source with.

USB mode

It is possible to project a video, picture, music or such from a USB device. Connect the USB device to one of the USB ports (7). Go to “Office suite” on the homepage and enter. Choose the kind of media you want to display. All files in the same category will show. Navigate to the file you want to view and press OK to project on the screen.

WiFi connection

It is possible to connect to the projector with WiFi to mirror your phone’s screen.

WiFi. iOS devices

1. Go to the settings menu. Enter the WiFi settings and choose your home network from the list and add it.
2. Go back to the homepage and enter “iOS cast”.
3. Open the WiFi settings on your iOS device and make sure the WiFi function is on. Connect your device to the same WiFi as the projector.
4. Swipe down on the screen of your device to open the control center. Select “Screen mirroring”. Connect to the iOS cast receiver named “Plex gear P100”. Your iOS device’s screen will be displayed on the projection screen after 3 seconds.

WiFi, Android devices

1. Go to the homepage and enter “Miracast”.
2. Swipe down on the screen of your Android device to open the control center. Look for “Smart-view” and select the Miracast receiver named “Plex gear P1 DD”. Your Android device’s screen will be displayed on the projection screen after 3 seconds.
3. Open the WiFi settings on your device and connect to your home network.

Note! The instructions for screen-view might vary from different Android brands and devices. Refer to your device’s manual for correct instructions.
Not all Android devices supports the Miracast function.

Pairing with Bluetooth

It is possible to pair the projector with Bluetooth devices such as headphones and speakers.
Go to the settings menu and choose the “Bluetooth” option. Start your Bluetooth device and activate its pairing mode. The projector scans for Bluetooth devices automatically. Select your Bluetooth device, pairing occurs automatically.

Image settings

Go to the settings menu and choose “Projection mode”. Select the correct option based on the placement of the projector (see illustration on page 4).

Keystone correction

If the projection screen is not rectangular due to the projector not standing on a horizontal surface with the lens perpendicular to the screen, you can correct this with the 4-point keystone correction.
Go to the settings menu. Select the “Keystone correction” menu and go to the “4-point keystone” option.
Use the arrows to correct the coordinates of the projection and press OK to switch coordinates.

Digital zoom

Go to the settings menu and choose “Keystone correction”. Go to the “Digital zoom” option to be able to zoom the projection. Use the left and right arrow buttons on the remote control or the projector to zoom in and out.
Press and hold the Menu button (19) to reset the zooming.

Reset

Enter the settings menu and go to “Other settings”. Choose to reset to factory settings to reset. All your own settings will disappear.

Troubleshooting

The remote control does not work.

Make sure the Power switch (11) is turned to On.
The battery level might be low. Change the batteries in the remote control and try again.
Make sure there is not anything in between the remote control and the IR receiver of the projector that can obstruct the signal. Make sure that there is no strong light directly on the IR receiver.
There is no image on the projection screen or only a blue screen and no sound
Make sure all cables are correctly connected and that you have chosen the same input source as the kind of cable you are using between the video source and the projector.

There is no sound.

Make sure the input cables are correctly connected and that the sound is not muted or the volume is on minimum.

The projector turns off unexpectedly.

The ventilation is blocked or the over-heating system has been activated. Make sure the ventilation is not blocked and let the projector rest for a while before restarting it.

Surround sound does not work.

This projector does not support Dolby Atoms or surround sound.

Safety information

Do not block any air outlets. Keep the projector in a well-ventilated and dry location.
Do not look directly at the lens when the projector is working.
Keep the projector out of reach from children.
Do not use chemicals, detergents or water to clean the projector. Keep the projector away from liquids.
Do not repair the projector yourself.

Simplified EU Declaration of Conformity

Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available
at www.kjell.com/24017

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>