Treevol Furniture WHFP041 Multi Functional Dresser Carlin Instruction Manual
- September 6, 2024
- Treevol Furniture
Table of Contents
WHFP041 Multi Functional Dresser Carlin
“`html
Specifications:
- Wood dowel: 38 pieces
- Spreading bolt: 44 pieces
- Minifix cam: 44 pieces
- Cover caps: 50 pieces
- Hinge + screws: 4 sets
- Wall anchor + screw: 2 sets
- Nail-on glide: 8 pieces
- Corner Support: 4 pieces
- Handle + screws: 3 sets
- Drawer slides + screws: 1 set
- Back panel support: 8 pieces
- Closet rod support: 2 pieces
- Drywall screw: 4 pieces
- Flat head screw: 20 pieces
- Closet rod: 1 piece
Product Usage Instructions:
What You Will Need:
Hi! my name is Armando, and I’ll be with you while you assemble
this cabinet.
- Phillips head screwdriver
- Flat head screwdriver
- Hammer
- A flat, smooth surface (cardboard or rug)
- (Optional) Electric screwdriver for easier assembly
Assembly Steps:
1. Start by Checking Panel and Hardware Content:
Verify that you have the correct quantity of each panel and
hardware component listed in the manual.
2. Wood Dowels and Minifix System:
Follow these steps when using wood dowels and the Minifix
system:
- Wood Dowels:
- Insert the dowel into the indicated hole.
- Gently hit the dowel until it’s fully inside to adjust the
joint.
- Minifix System:
-
Insert the Minifix cam with the arrow pointing towards the
panel’s edge. -
Secure the joint by turning the spreading bolt.
3. Assembling the Cabinet:
Follow the detailed instructions provided in the manual for
assembling the cabinet panels in the correct sequence.
4. Drawer Slides Installation:
Ensure the wheel of the drawer slide faces towards the front
edge of the panel and is installed securely with screws.
5. Final Steps:
Turn over the cabinet carefully and slide the back panels into
the grooves as instructed.
FAQ:
Q: What should I do if I lose a hardware component?
A: If you lose a hardware component, please contact customer
support for assistance in obtaining a replacement to complete the
assembly process.
Q: Can I use additional tools for assembly?
A: While an electric screwdriver is optional, it can make the
assembly process easier and faster. However, ensure not to
overtighten screws to prevent damage to the cabinet.
“`
ASSEMBLY INSTRUCTIONS
DRESSER
It’s much better if you get some company for this!
LOT N°
Index
What will you need?
2
Where should you start?
3
What’s in the hardware bag?
4-5
How do the dowels and Minifix system work?
(We also explain what they are)
6
Let’s start assembling!
7
How much weight does your cabinet resist?
24
Our last recommendations for taking care of your cabinet
25
What will you need?
Hi! my name is Armando, and I’ll be with you while you assemble this cabinet.
Phillips head screwdriver Flat head screwdriver Hammer
A flat, smooth surface. You can use the cardboard of the box or a rug.
An electric screwdriver isn’t necessary, but it can make the work much easier
🙂
2
Where should you start?
This is so IMPORTANT!
Over the next few pages is the panel and hardware content for this
cabinet. Please make sure that the quantity
of each one is correct, and that everything is in good shape.
(When the cabinet is already assembled there’s no warranty for this)
Panel quantity
A – x1 E – x1 I – x1 M – x1 Q – x1
B – x1 F – x2 J – x1 N – x2 R – x1
C – x1 G – x1 K – x1 O – x1 S – x1
D – x1 H – x1 L – x1 P – x1
3
What’s in the hardware bag?
Wood dowel
x38
Spreading bolt
x44
Minifix cam
x44
Cover caps
x50
2 1/2″
Hinge + screws
x4
Wall anchor + screw x2
Nail-on glide
x8
Corner Support
x4
Handle + screws
x3
Drawer slides + screws
x1
Back panel support x8
Closet rod support x2
4
2″ 9/16 ” 3/4 ”
Drywall screw
x4
Flat head screw
x12
Flat head screw x8
Closet rod x1
Be careful!, try not to lose anything from this bag, its content is necessary for assembling your cabinet.
5
How do the dowels and Minifix system work?
this is so important too!
Everytime you’re using one of these connectors during the assembly, you
should follow these same steps.
Wood dowels
They are little wooden cylinders.
When joining two
1
Put in the dowel
2
inside the indicated
panels together, don’t forget to gently hit
hole and softly hit it
the panels to adjust
until it’s fully inside.
the joint.
Minifix system
It’s a joint compound of two parts: a spreading bolt and a Minifix cam.
1
small arrow
This is a Minifix cam.
3
It has a little arrow on its
upper surface.
This is a spreading bolt. You should put it with the black plastic part facing down.
2
You should insert these cams
with the little arrow pointing towards the drilling on the
4
panel’s edge (shown on the
left).
After joining two panels together you should turn the
cams 180° with a phillips head screwdriver to adjust
and secure the joint.
6
1 Let’s start assembling!
You can see the last page of this manual to have a full look of the panels of
this cabinet.
B
2
F x2
7
3
F B F
Turn these panels over
B F
8
4 Drawer slides installation (apply for steps 4 and 6)
The wheel should go towards the front edge of the panel and facing down, like this:
4
13
Down
Front
Down
E
Turn this panel over
Front
Flat head screw
E
9
5
F B E
6
To recall the slides installation
you can go to the 4th step
again.
13
4
Down
C
Front
10
7
O Q
8
S
11
9
S Q
C
O
10
F B
E S
Q C
O
12
11
D
12
P R
13
13
R P
D
14
F
B D
R
E S
Q C
P O
14
15
Turn over the cabinet
very carefully!
Slide the back panels inside the grooves.
N
N
Q
P O
D
E
C
B
F
15
16
A
17
A
Q
R
S
C
N
E
ND
B
F
16
18 2
Back Panel Support
N
N
Flat head screw 3/4″.
Insert the back panel supports between the groove
and the back panel.
Fix the back panel supports with a 3/4″ flat head screw.
A
P
2
O
2
N
2
2
2
2
N
C
1
2
1
1
2
F
1
Install this Corner Support inside the cabinet
1
Corner Support
N
Flat head screw 9/16″ Place the corner supports in the lower corners and fix
them with a 9/16″ flat head screw.
17
19
Fix your cabinet to the wall
1 On the wall, measure and mark the points shown below. 2 Drill on the
markings with a 5/16″ drill bit. 3 Insert the wall anchors inside the
drillings. 4 Place the cabinet and secure it with the screws.
9,21
17,40
9,21
O
P
2,58
*Dimensions in inches
34,31
18
20
I H
21
I
Drywall screw 2″
J H
19
22
Slide the back panel inside the grooves.
I J
M
H
23
K
20
24
K M
J
I
25
Putting the drawers in
The wheel should go on the rear part of the drawer.
M J
IK
21
26
A
Q
R
K
I
C
N
E
N
D
Slide the drawer inside the cabinet.
B F
22
27Assembling and setting up the door
A
K
R
S
C
G
E
D
B
L
F
Hinge adjustment
Depth adjustment
Lateral adjustment
After adjusting all the Minifix cams, cover
them up with the cover caps.
Height adjustment
Front screws adjustment
A
After finishing the assembly, lift off al the
adhesive letters.
23
How much weight does my cabinet resist?
22
11
22
22
*weight in pounds
Congratulations! It’s done
But don’t go yet!
There are some recommendations left for you to take care of your cabinet
correctly from now on.
SUPER IMPORTANT!
We suggest fixing the cabinet to the wall, so we can avoid the cabinet tipping
and harming anyone. Be specially careful with the kids.
24
Taking care of your cabinet:
Do not paint the cabinet. The cabinet it’s exclusively for indoor spaces. Do
not expose it to the direct sun. Clean the metallic hardware with a dry cloth.
DO NOT overload the cabinet (see suggested loads) Do not hit or hammer the
cabinet (only when indicated here). Clean it with thinner, a soft soap
solution or simply a damp cloth. Don’t drag the cabinet, lift it up with other
people. Avoid direct contact with water, fire or exposing it to high heat.
Cabinet panels
H
J M
K
I
C G
A
O P
Q
S
R
E
B F F
D L
N N
25
WARRANTY POLICY
PÓLIZA DE GARANTÍA
Furniture has a 3 year warranty coverage in wooden parts and 1 year warranty
coverage in hardware pieces since its manufacturing date, which you can see in
the lot number printed on the product box and the assembly instructions
leaflet. Warranty covers materials and workmanship imperfections which impair
the assembly or correct functioning of the cabinet. This warranty is not valid
if the defects or imperfections are caused by the incorrect following of the
assembly instructions, warnings and recommendations, misuse, intentional
damage, fire or flood, or after modifications or any kind of alteration, or
repaired by someone not authorized, when it´s been assembled 3 months after
the date of purchase. These defects MUST be reported before the warranty
coverage period ends. Once the product has been assembled, the company will
not be responsible for defective and/or damaged parts. This warranty is ONLY
valid for the ORIGINAL PURCHASER, it doesn’t apply if the product has been
resold, rented, etc. Furniture will take no liability for incidental or
consequential damages caused to or by the product (This may not apply in your
state). To make this warranty valid you must write to our customer service
email describing the product defect, lot number and submitting your sales
reciept or proof of purchase, or contact us at our customer service line.
Replaced parts will be under the product´s original warranty coverage period.
Damaged parts will become property of the company. There are no other
warranties applicable to this product.
26