COOPER Lighting Solutions IB50533821 Sure-Lites Apel Mini Emergency Light Instruction Manual

COOPER Lighting Solutions IB50533821 Sure-Lites Apel Mini Emergency Light

Important Safeguards

When using electrical equipment, basic safety precautions should always be observed including the following.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

• Do not use outdoors.
• Do not mount near gas or electric heaters.
• Do not let power supply cords touch hot surfaces.
• Do not use this equipment for other than the intended use.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
• Install in accordance with National Electric Code and local regulatory agency requirements.
• Installation is to be performed only by qualified personnel.
• DO NOT EXCEED TOTAL OUTPUT RATING of source power equipment

SAVE THESE INSTRUCTIONS

WARNING

• Risk of Fire, Electrical Shock or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved.
• Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
• Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
• Risk of Personal Injury- Due to sharp edges, handle with care.

DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
Note: Specifications and dimensions subject to change without notice.
NOTICE: Fixture may become damaged and/or unstable if not installed properly.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Wall Mount Installation

1. Extend unswitched 24-hour AC supply of rated voltage to junction box. Leave at least 8 inches of slack. Circuit should not be energized at this time.
2. Open the APELMINI by inserting a screwdriver at the two holes on the bottom of the unit. This will deflect the snap features to allow the unit to open. (See Figure 1)
3. Knock out the appropriate mounting hole pattern and wire pass hole on the backplate to match junction box.
4. Install the backplate to the junction box using screws. Once the backplate is installed the unit can be hung from the EZ-Hang snap features to increase ease of installation. (See Figure 2)
5. Connect power supply and ground in accordance with local codes. Wire connections as follows: 277VAC line to orange lead or 120V line to black lead; neutral to white lead. Cap unused line lead (see Schematic).
6. Energize AC supply. Test Button will illuminate.

Conduit Installation

1. Extend unswitched 24-hour AC supply of rated voltage to device location. Leave at least 6 inches of slack. Circuit should not be energized at this time.
2. Open the APELMINI by inserting a screwdriver at the two holes on the bottom of the unit. This will deflect the snap features to allow the unit to open. (See Figure 1)
3. If mounting to conduit and using it as support, skip to step 4. If mounting to surface and using conduit as wire-way, knock out the appropriate mounting hole pattern on the backplate. Mount the backplate to the wall in the desired location.
4. Attach conduit hubs to the appropriate conduit entry points on the backplate.
5. Remove the correct conduit cover knockout(s) for your desired configuration of conduit access. (See Figure 3)
6. Connect power supply and ground in accordance with local codes. Wire connections as follows: 277VAC line to orange lead or 120VAC line to black lead; neutral to white lead. Cap unused line lead (see Schematic).
7. Snap housing back onto the backplate. Ensure no wires are pinched while re-assembling the unit.
8. Energize AC supply. Test Button will illuminate.

Maintenance

Equipment should be tested regularly in accordance with local codes.
Note: Servicing of any parts should be performed by qualified personnel. Only use replacement parts supplied by Cooper Lighting Solutions.

Troubleshooting guide

If LED heads or charge indicator LED does not illuminate, check the following:

• Check AC supply – verify that unit has 24-hour AC supply.
• Unit is shorted, or battery is not connected.
• Battery discharged. Permit unit to charge for 24 hours and then re-test.
• If following the above troubleshooting hints does not solve your problem, contact your local Cooper Lighting Solutions representative for assistance.

Warranties and Limitation of Liability

Please refer to www.cooperlighting.com for our terms and conditions.

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com

Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172

© 2022 Cooper Lighting Solutions All Rights Reserved
Publication No. IB50533821
March 14, 2022 049-336
Cooper Lighting Solutions is a registered trademark. All trademarks are property of their respective owners.
Product availability, specifications, and compliances are subject to change without notice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>