Solar Lighting DIRECT SLDBL002-BLK-DC Commercial Bollard in Stainless Steel Instructions

September 24, 2024
Solar Lighting DIRECT

Solar Lighting DIRECT SLDBL002-BLK-DC Commercial Bollard in Stainless

Steel

Product Information

Specifications:

  • Model No.: SLDBL002/BLK-DC, SLDBL2602/BLK-DC, SLDBL2602/SS-DC, SLDBL007/BLK-DC, SLDBL007/SS-DC, SLDBL007/AL-DC
  • Power Source: Solar
  • Light Output: Dual Colour Technology (Warm White/Cool White)
  • Operation Modes: Auto Day-Night, Dusk to Dawn
  • Charging Time: 6 hours direct sunlight recommended

Product Usage Instructions

Installation:

  1. Remove contents from packaging.
  2. Place the solar panel in a location where it can receive a minimum of 6 hours of direct sunlight.
  3. If the light does not turn on automatically in Auto Day-Night mode, follow these steps:
  4. Remove the grommet as shown in Figure 1.
  5. Hold the red power button for approximately 3 seconds to activate the light.
  6. To switch to Dusk to Dawn mode, remove the solid surface covering the panel.

Changing LED Output Color:

  1. Repeat Step 2 of the installation process.
  2. Locate and remove the rubber grommet at the top of the bollard (location varies).
  3. Use a tool to find the red press button and alternate between warm white and cool white.
  4. The light will automatically turn on in the chosen color setting.

Troubleshooting:

Phenomenon Cause Inspection Method Solution
Light won’t turn on Switch off, low battery, insufficient light Detect

switch position, check battery charge, ensure adequate
light| Turn switch on, charge battery in sunlight, clean solar
panel
Battery Failure| Moved or damaged battery, battery needs replacement| Check battery status and contact customer service for
replacement| Contact Customer Service Number: 1300 135 911

FAQ:

  • Q: Can I install the lights under a street light or porch light?
    A: It’s best not to install these lights underneath a street light or porch light as it may interfere with the automatic day-night sensor triggering.

  • Q: How do I ensure the battery reaches full capacity?
    A: Place the solar panel in a location where it can achieve a minimum of 6 hours of direct sunlight. In overcast conditions, the panel will still charge but may not reach full capacity.

INSTALLATION METHOD

  1. Remove contents from packaging
    Note: The light will blink when exposed to daylight indicating the light is now on and in Auto Day-Night operation Mode. If this doesn’t happen remove the grommet as per Figure 1 below and hold in red power button for approx 3 seconds to activate light.

  2. Temporarily cover solar panel with solid surface for testing purposes only – Light should illuminate

  3. Remove the solid surface & the light will turn off. The light is now in Dusk to Dawn Mode and ready to use

Models with Dual Colour Technology
In order to change the colour of the LED output from Warm White/Cool White:

  1. Repeat Step 2 above
  2. Locate and remove rubber grommet towards the top of the bollard (See in FIGURE 1)(location varies on each bollard)
  3. Use an appropriate size tool (i.e. screwdriver) and gently insert it into the space and find the red press button
  4. Pushing this button momentarily will allow you to alternate between warm white and cool white
  5. Once you have set your chosen colour the light will automatically turn back on in this setting.

Installation Tips

  • Make sure you select the best area where the solar panel of your light will receive the most direct sunlight during the day
  • We recommend you put your solar panel in the sun for 2 days before installation

IMPORTANT NOTES

  • Please ensure you place your solar panel in a location where it can achieve a minimum of 6HRS DIRECT SUNLIGHT
  • Be aware that with overcast/cloudy days, the solar panel will still charge. However, not as efficiently as a sunny day, so the battery may not reach full capacity. Therefore turning off earlier than specified
  • It’s best not to install these lights underneath a street light, porch light etc. because this may stop the automatic day-night sensor triggering and result in your lights not turning on

TROUBLESHOOTING

Phenomenon Cause Inspection Method Solution
Light won’t turn on Switch hasn’t been turned on Detect what position the
switch is in Turn the switch on
Battery has run out Long rainy days or installation site doesn’t provide
enough light Charge the light in direct sunlight for 1-

2 days then check again

Short lighting time| Low Battery| 1. Bad installation site for the light

2. Dust and leaves are covering the panel

3.  Long period of rainy days

| 1.  Charge the battery in direct sunlight for 1-2 days with switch off, then check again

2. Clean the solar panel

Battery Failure| 1.  Access the light and check if the battery has moved or if it has been damaged

2.  Battery has matured and requires replacing

| Contact us to replace your battery

Customer Service Number: 1300 135 911
www.solarlightingdirect.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Solar Lighting DIRECT User Manuals

Related Manuals