VENETA 65101-10234-I Cordless Honeycomb Blind Models Installation Guide
- June 9, 2024
- Veneta
Table of Contents
VENETA 65101-10234-I Cordless Honeycomb Blind Models
Required Tools
- measuring tape
- drill with 2mm bit
- phillips bit or screw driver
- pencil
- knife
Included Hardware
The hardware can be found in the end of every box.
Installation Bracket
- 25mm Single (Cordless Bottom Up only)
- 45mm Single 45mm Double (Cordless Bottom Up)
- Cordless TDBU, Day&Night
- Handle
- Medium & Long Screws for Wood
- Wall Plugs for Brick or Cement using a 6mm bit (if requested)
- Extension Pole (if requested)
Child Safety
This product has no cord control or chain and is safe for use around young
children!
Installation Brackets
Installing inside the window frame…
- At top of window frame, measure 75mm in from each end and mark with a pencil; this is the centre of the outer brackets.
- Place brackets in position 5mm back from the front of the window opening and mark where the screws will go.
- We recommend drilling pilot holes for the screws using a 2mm bit. Fix the brackets into position using 2 long screws for each bracket into the first two holes closest to the front of the bracket.
- If more brackets are supplied, space them evenly between the first two brackets.
Installing outside the window frame…
- Measure 75mm in from top left and top right of where the blind will sit (normally edge of architrave) and mark where the screws will go.
- We recommend using a spirit level to align brackets if not installing on the architrave.
- We recommend drilling pilot holes for the screws using a 2mm bit.
- Fix the brackets into position using 2 long screws for each bracket.
- If more brackets are supplied, space them evenly between the first two brackets.
Install Blind
- Position the top front lip of the blind under the top front lip of the brackets.
- Push the blind up at the back to click into position as per diagram to the right.
Attach Handle
- Step 1. Position the handle at an angle as shown below so that it is hooked to the rail.
- Step 2. Then push it to snap into place, there will be a “Click” sound.
- Step 3. Check if handle’s upper and lower hooks firmly hook to the rail.
Middle Rail for Cordless TDBU, Day & Night
Bottom Rail for Cordless, Cordless TDBU, Day & Night
Great Job… Enjoy your new Veneta Blind!
Operating your Blind
Bottom Up
- Lower and raise the blind using the handle on the bottom rail.
TDBU, Day &Night
- Lower and raise the blind using the handles on the bottom and middle rails.
Note: You must first lower the bottom rail before lowering the middle rail.
Note: You must first raise the middle rail before raising the bottom rail.
Maintaining your Blind
Removing your Blind
- For Cordless Bottom Up
- Position a flat head screw driver between the back of the headrail and bracket.
- Push screw driver upwards.
- Pull back of headrail down to unclip bracket from headrail.
- Repeat for all other brackets.
For Cordless TDBU, Day & Night
- For Cordless TDBU, lower the middle rail.
- For Cordless Day & Night, fully raise the shade.
- Position a flat head screw driver between the back of the headrail and center of the backet, and push up the flip on the bracket.
- While pushing upwards, gently swing the screwdriver forward to pry the bracket off the head rail.
- Repeat for all other brackets.
Feedback?
We would love to know how you went with your installation…
Please write a review on our website at…
www.venetablinds.com.au
Need HELP?
Call our Customer Service team for assistance 1300 836 382
Dusting
- Dust can be removed using a feather duster or vacuum with brush attachment on low suction.
Spot Cleaning
- Use a warm damp cloth or a mild detergent for tougher stains.
- Dab the affected area, but do not rub the fabric.
- Finish with just a warm damp cloth.
- Allow the fabric to dry in the lowered position.
Ultrasonic
- If ultrasonically cleaning the blind please specify that a mild solution must be used.
- Note the rails should never be immersed in liquid.
References
Read User Manual Online (PDF format)
Loading......