BEGA 50084.1 Indoor Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
50 084.1
Wall luminaire for indoor use
Instructions for use
50084.1 Indoor Wall Luminaire
Application
Open and free-radiating wall luminaire · indoor luminaire with hand-blown opal
glass and metal housing.
The character of the opal glass creates a smooth and uniform light
distribution in the room.
Product description
Metal luminaire housing, finish Colour white Hand-blown opal glass 2 mounting
holes Ø 6.5 mm Distance apart 520 mm Connection terminal 2.5@ Earth conductor
connection 2-pole connecting terminal for digital control LED power supply
unit 220-240 V 0/50-60 Hz DC 176-276 V During DC operation the LED power is
reduced to 15 % DALI-controllable Number of DALI addresses: 1 Basic insulation
is provided between the mains and control cables BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire Safety class I
– Safety mark
**– Conformity mark
Weight:** 3.0 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage| 29.4 W
Luminaire connected wattage| 35 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 45 °C
50 084.1 K3
Module designation| 2x LED-0626/930 + 2x LED-0627/930
Colour temperature| 3000 K
Colour rendering index| CRI > 90
Module luminous flux| 4650 lm
Luminaire luminous flux| 3999 lm
Luminaire luminous efficiency| 114,3 lm / W
Installation
Only fix luminaire in position of application as pictured.
For revamping, mounting and dismantling of the glass please keep a distance of
600 mm above the luminaire.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or revamping.
Establish earth conductor connection and make the electrical connection to the
terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
Secure the luminaire housing to the installation surface with the fixing
materials provided or other suitable materials.
Note position of application “arrow down”.
Loosen the knurled knob.
Position glass into luminaire housing and fix it with the knurled knob.
Cleaning – Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation
instructions for the LED module.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass| 11 003 228 .1R G
LED power supply unit| DEV-0159/1050i
LED module 3000 K| LED-0627/930
LED module 3000 K| LED-0626/930
BEGA Gantenbrink-Leucite KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>