Solar Lighting DIRECT SLDBL008-GRY-DC Industrial Bollard Light Instruction Manual
- June 1, 2024
- Solar Lighting DIRECT
Table of Contents
Solar Lighting DIRECT SLDBL008-GRY-DC Industrial Bollard Light
Product Information
Specifications:
- Model Numbers: SLDBL008/GRY-DC, SLDBL0011/BLK-DC, SLDBL0012/BLK-DC, SLDBL0086/GRY-DC, SLDBL0013/BLK-DC, SLDBL2713/BLK-DC
- Features: Dual Colour Technology, Auto Day-Night operation Mode, Dusk to Dawn Mode
- Additional Feature: Supplementary LED Decorative Light
- Customer Service Number: 1300 135 911
- Website: www.solarlightingdirect.com.au
Product Usage Instructions
Installation Method:
- Remove contents from packaging.
- For Auto Day-Night operation Mode:
- If the light does not blink when exposed to daylight, remove the grommet as per Figure 1 and hold the red power button for approximately 3 seconds to activate the light.
- For Dusk to Dawn Mode:
- Remove the solid surface to turn off the light.
- For Models with Dual Colour Technology:
- Repeat Step 2 above.
- Locate and remove the rubber grommet towards the top of the bollard.
- Use an appropriate tool to find the red press button and alternate between warm white and cool white.
Important Notes:
- Place the solar panel where it can achieve a minimum of 6 hours of direct sunlight.
- Avoid installing lights under street lights or porch lights to ensure proper day-night sensor triggering.
- Pre-installation tip: Put the solar panel in the sun for 2 days before installation.
Troubleshooting:
- Phenomenon: Light won’t turn on
- Cause: Switch hasn’t been turned on
- Inspection Method Solution: Detect the switch position and turn it on
Frequently Asked Questions (FAQ):
- Q: What should I do if my light still doesn’t turn on after following troubleshooting steps?
A: Contact customer service at 1300 135 911 for further assistance.
INSTALLATION METHOD
-
Remove contents from packaging.
Note: The light will blink when exposed to daylight indicating the light is now on in Auto Day-Night operation Mode. If this doesn’t happen remove the grommet as per Figure 1 below and hold in red power button for approx 3 seconds to activate light. Repeat this process to switch off. -
Temporarily cover solar panel with solid surface for testing purposes only – Light should illuminate.
-
Remove the solid surface & the light will turn off. The light is now in Dusk to Dawn Mode and ready to use.
Models with Dual Colour Technology
In order to change the colour of the LED output from Warm White/Cool White:
- Repeat Step 2 above.
- Locate and remove rubber grommet towards the top of the bollard (See in FIGURE 1 & 2)(location varies on each bollard).
- Use an appropriate size tool (i.e. screwdriver) and gently insert it into the space and find the red press button.
- Pushing this button momentarily will allow you to alternate between warm white and cool white.
- Once you have set you chosen colour the light will automatically turn back on in this setting.
Note: SLDBL0086-GRY/CW has a “Supplementary LED Decorative Light” feature
as well as Dual Colour Technology – this product has 2 grommet holes; one for
Dual Colour and one for the Feature Strip Lighting (See in FIGURE 2)
IMPORTANT NOTES
- Please ensure you place your solar panel in a location where it can achieve a minimum of 6HRS DIRECT SUNLIGHT
- Be aware that with overcast/cloudy days, the solar panel will still charge. However, not as efficiently as a sunny day, so the battery may not reach full capacity. Therefore turning off earlier than specified.
- It’s best not to install these lights underneath a street light, porch light etc. because this may stop the automatic day-night sensor triggering and result in your lights not turning on
Installation Tips
- We recommend you put your solar panel in the sun for 2 days before installation
TROUBLE SHOOTING
| Phenomenon | Cause | Inspection Method | Solution |
|---|---|---|---|
| Light won’t turn on | Switch hasn’t been turned on | Detect what position the | |
| switch is in | Turn the switch on | ||
| Battery has run out | Long rainy days or installation site doesn’t provide | ||
| enough light | Charge the light in direct sunlight for 1-2 days then check |
again
Short lighting time| Low Battery| 1. Bad installation site for the light
2. Dust and leaves are covering thepanel
3. Long period of rainy days
| 1. Charge the battery in direct sunlight for 1-2 days with switch off, then check again
2. Clean the solar panel
Battery Failure| 1. Access the light and check if the battery has moved or if it has been damaged
2. Battery has matured and requires replacing
| Contact us to replace your battery
Customer Service Number: 1300 135 911
www.solarlightingdirect.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>