Solar Lighting DIRECT SLDWL0022-BLK-WW Solar Powered Flush Mounted Wall Light with Motion Sensor Instruction Manual
- June 1, 2024
- Solar Lighting DIRECT
Table of Contents
Solar Lighting DIRECT SLDWL0022-BLK-WW Solar Powered Flush Mounted Wall
Light with Motion Sensor
Product Information
- Specifications:
- Model No.: SLDWL0022/BLK-WW, SLDWL0022/SS-WW
- IP44 Waterproof Rating
- Pyro-electric Infrared Sensor
- Built-in Photo Electric Cell (Day/Night Sensor)
- 3 Operation Settings
- 6-9 Hours of Operation per day
- 4-6 Hours Charge time
- Flush Wall Mount Base
- Warm White LEDs
Product Usage Instructions
- Installation:
- Remove contents from packaging.
- Decide where to mount your wall light.
- Refer to FIGURE 1 for the following steps:
- Drill 3 holes in your chosen wall as per the dimensions & insert the plastic anchors.
- Insert the screw into the anchor at point (1) leaving the screw to project 5mm from the wall, now fix the light onto the wall by hooking the Keyhole over the screw at point (1).
- Finally, insert screws into points (2 & 3) from the front of the fitting to tightly secure.
- Important Notes:
- Place your Solar Panel in a location where it can achieve a minimum of 6 DIRECT SUNLIGHT.
- Avoid installing lights underneath a street light, porch light, etc., as this may interfere with the day-night sensor triggering.
FAQs
- Q: How long does it take to charge the battery initially?
- A: It takes approximately 4-6 hours for the battery to fully charge initially.
- Q: Can the light function in rainy or overcast weather?
- A: The solar panel can still charge on overcast/cloudy days, but not as efficiently as on sunny days. The light may turn off earlier than specified in such conditions.
PACKAGE CONTENTS
- 1 x Light Fitting
- 1 x Pack of mounting screws
FEATURES
- IP44 Waterproof Rating
- Pyro-electric Infrared Sensor
- Built-in Photo Electric Cell (Day/Night Sensor)
- 3 Operation Settings
- 6-9 Hours of Operation per day
- 4-6 Hours Charge time
- Flush Wall Mount Base
- Warm White LEDs
LIGHT FUNCTIONS
- Green Indicator Light – A dim 40-lumen light stays on constantly throughout the night when no motion is detected. When the motion sensor is triggered the light goes to 150 lumen brightness and stays on for 40 seconds before switching back to dim.
- Blue Indicator Light – The light is completely off until the motion sensor is triggered. When triggered, the light comes on at 200 lumen brightness and stays on for 40 seconds.
- Red Indicator Light – The light comes on at night at 30 lumens and stays on the remainder of the night.
INSTALLATION METHOD
-
Remove contents from packaging
-
Decide where to mount your wall light (where the light will receive maximum direct sunlight – See “Important Notes”)
-
Press the button on the front face of your light “ON” to your desired setting.
Please refer to FIGURE 1 for the following steps: -
Drill 3 holes in your chosen wall as per the dimensions & insert the plastic anchors.
-
Insert the screw into the anchor at point (1) leaving the screw to project 5mm from the wall, now fix the light onto the wall by hooking the Keyhole over the screw at point (1).
-
Finally, insert screws into points (2 & 3) from the front of the fitting to tightly secure.
IMPORTANT NOTES
- Please ensure you place your Solar Panel in a location where it can achieve a minimum of 6HRS DIRECT SUNLIGHT
- Be aware that on overcast/cloudy days, the solar panel will still charge. However, not as efficient as a sunny day, so the battery may not reach full capacity. Therefore, your light may turn off earlier than specified.
- It’s best not to install these lights underneath a street light, porch light etc. because this may stop the automatic day-night sensor triggering and result in your lights not turning on
TROUBLESHOOTING
- Customer Service Number: 1300 135 911
- www.solarlightingdirect.com.au.
- Model No. SLDWL0022/BLK-WW, SLDWL0022/SS-WW
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>