Solar Lighting DIRECT SLDWL0099A-BLK-WW Solar Powered Stainless Steel Flush Mount Wall Light Instruction Manual
- June 1, 2024
- Solar Lighting DIRECT
Table of Contents
Solar Lighting DIRECT SLDWL0099A-BLK-WW Solar Powered Stainless Steel
Flush Mount Wall Light
Product Information
Specifications:
- Model No.: SLDWL0099A/BLK-WW, SLDWL0099A/SS-WW, SLDWL0099A/SS-CW
- IP65 Waterproof Rating
- Pyro-electric Infrared Sensor
- Built-in Photo Electric Cell
- Self-adjusting run time on Sensor
- 8-10 hours Operation per day
- Flush Wall Mount Base
Product Usage Instructions
Installation Method:
- Remove package contents.
- Put the light in direct sunlight (switch off) for 2 days before installation.
- Decide the mounting location for maximum sunlight exposure throughout the day.
Installation Steps:
- Ensure the light switch is in the ON position.
- Drill a hole in the wall, insert a plastic anchor, and screw in leaving 5mm exposed.
- Hook the keyhole at the back of the light over the mounted screw securely.
Important Notes:
- Place a Solar Panel where it can get a minimum of 6 hours of direct sunlight.
- Solar panels may charge less efficiently on overcast days affecting battery capacity.
- Avoid installing under street lights or porch lights to ensure automatic sensor functionality.
Troubleshooting:
| Phenomenon | Cause | Inspection Method | Solution |
|---|---|---|---|
| Light won’t turn on | Switch off or low battery | Determine switch position and | |
| battery level | Turn switch on or charge battery in direct sunlight | ||
| Light stays on for a short time | Rainy/cloudy weather or low battery | Check | |
| battery level and solar panel condition | Charge battery in direct sunlight or |
clean solar panel
Contact Customer Service:
- Customer Service Number: 1300 135 911
- Website: www.solarlightingdirect.com.au
FAQ:
-
Q: How long does the light operate per day?
A: The light operates for 8-10 hours per day. -
Q: Can the light be installed under street lights?
A: It’s not recommended to install the light under street lights as it may affect the automatic sensor triggering.
PACKAGE CONTENTS
- 1 x Light Fitting
- 1 x Pack of Screws
FEATURES
- IP65 Waterproof Rating
- Pyro-electric Infrared Sensor
- Built in Photo Electric Cell
- Self-adjusting run time on Sensor
- 8-10 hours Operation per day
- Flush Wall Mount Base
INSTALLATION METHOD
-
Remove package contents
NOTE: Before continuing, we recommend you put your light in direct sunlight (with the switch in the “OFF” position) for 2 days before installation -
Decide where to mount your wall light (where the light will receive maximum direct sunlight throughout the day)
Please refer to FIGURE 1 for the following steps:
- Step 1. Make sure your light is switched in the “ON” position (D).
- Step 2. Drill a hole in your chosen wall large enough to fit the plastic anchor (C) and insert anchor.
- Step 3. Insert screw (B) into the anchor, make sure it is in tight but leave 5mm of the screw to project out of the wall.
- Step 4. Fix the wall light (A) by hooking the keyhole at the back of the light, over the mounted screw and make sure the light is on securely.
IMPORTANT NOTES
- Please ensure you place your Solar Panel in a location where it can achieve a minimum of 6HRS DIRECT SUNLIGHT.
- Be aware that on overcast/cloudy days, the solar panel will still charge. However, not as efficiently as a sunny day, so the battery may not reach full capacity. Therefore, your light may turn off earlier than specified.
- It’s best not to install the fitting underneath a street light, porch light etc. because this may stop the automatic day-night sensor triggering and result in your lights not turning on.
TROUBLE SHOOTING
Customer Service Number: 1300 135 911
www.solarlightingdirect.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>