Solar Lighting DIRECT SLDFL25W-PIR-CW Residential Flood Light Instruction Manual
- June 1, 2024
- Solar Lighting DIRECT
Table of Contents
Solar Lighting DIRECT SLDFL25W-PIR-CW Residential Flood Light
Product Information
Specifications:
- Model: SLDFL25W-PIR-CW
- Light Fitting: 25W Residential Flood Light
- Solar Panel : 15W Polycrystalline
- Mounting: Mounting Bracket & Screws included
- Remote Control: Yes
Product Usage Instructions
Installation:
- Remove contents from packaging.
- Switch button on the back of battery box to ON position.
- Choose the location to mount your flood light and solar panel.
Remote Operating Instructions:
Adjust the sensor settings according to your preference:
- OFF Manual Mode 1
- Brightness +/-
- ON Manual Mode 2
- Auto Mode 1
- Auto Mode 2
- TIME – Adjust the length of time the light remains on after the last motion detection (5s – 6m)
- SENS – Sensitivity adjustment of the sensor
Important Notes:
- Place the solar panel where it can receive a minimum of 6 hours of direct sunlight daily.
- On overcast days, the charging efficiency may reduce, affecting the battery capacity and light duration.
- Avoid installing the solar panel under street lights or porch lights to ensure proper day-night sensor operation.
Troubleshooting:
Phenomenon | Cause | Inspection Method | Solution |
---|---|---|---|
Light won’t turn on | Switch off or battery flat | Determine switch position or |
charge battery in direct
sunlight| Turn switch on or charge battery for 1-2 days
Light only stays on briefly| Low battery or battery failure| Charge the
battery in sunlight or replace battery| Contact customer service for battery
replacement
FAQ
- Q: What should I do if my light does not turn on?
- A: Check the switch position and ensure the battery is charged by exposing it to direct sunlight for 1-2 days.
- Q: Why does my light turn off quickly?
- A: This could be due to a low battery or battery failure. Charge the battery in direct sunlight or contact customer service for a replacement.
- Contact Solar Lighting Direct Customer Service at 1300 135 911 or visit www.solarlightingdirect.com.au for more information.
PACKAGE CONTENTS
- 1 x Light Fitting
- 1 x 15w Polycrystalline Solar Panel
- 1 x Pack Mounting Bracket & Screws
- 1 x Remote
INSTALLATION METHOD
- Remove contents from packaging
- Switch button on the back of battery box “ON”
- Decide where to mount your flood & panel
Flood – Secure the mounting bracket in your desired location, make sure
the length of cable will reach to the solar panel. Screw the flood onto the
bracket
Panel – Mount the panel on a nearby roof or wall where it will receive
maximum direct sunlight throughout the day. Attach cable from panel to flood
REMOTE OPERATING INSTRUCTIONS
- Button 1 – Manual Mode 1 – When pressed, this button will set your light to operate manually via the “ON/OFF” buttons on the remote control
- Button 2 – Manual Mode 2 – When pressed, this button will set your light to operate manually day or night & by-passes the Dusk to Dawn feature of the on-board smart controller, it will illuminate when the PIR sensor detects movement. When no further movement is detected the light will switch off and await further triggers from the sensor
- 25% Button – Auto Mode 1 – When pressed, this button will set your light to operate automatically from Dusk to Dawn via the onboard smart controller, it will remain illuminated until it becomes daylight or the battery loses charge. This function is controlled by the Solar Panel
- Mode Button – Auto Mode 2 – When pressed, this button will set your light to operate automatically from Dusk to Dawn via the onboard smart controller and illuminate when the PIR sensor detects movement. Once no further movement is detected the light will switch off and await further triggers from the sensor
IMPORTANT NOTES
- Please ensure you place your solar panel in a location where it can achieve a minimum of 6HRS DIRECT SUNLIGHT
- Be aware that on overcast/cloudy days, the solar panel will still charge. However, not as efficient as a sunny day, so the battery may not reach full capacity. Therefore, your light may turn off earlier than specified
- It’s best not to install the solar panel underneath a street light, porch light etc. because this may stop the automatic day-night sensor triggering and result in your lights not turning on
TROUBLESHOOTING
ADJUSTING THE SENSOR
LUX
- When set to the sun – the sensor will work during day
- When set to the moon – the sensor will work at night
- TIME – Length of time light will remain on for after last motion detection (5s – 6m)
- SENS – Sensitivity adjustment of the sensor
CONTACTS
- Customer Service Number : 1300 135 911
- www.solarlightingdirect.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>