bouncepad BP-COR-WAL-W Core Wall Mount Installation Guide
- September 12, 2024
- bouncepad
Table of Contents
BP-COR-WAL-W Core Wall Mount
“`html
Specifications:
-
Product Name: Core Wallmount
-
Sheet Code: BP-IM-083_REV0
-
Release Date: 13/08/2024
-
Maximum Mounting Surface Thickness: 25mm (Metric) / 1 inch
(Imperial) -
Minimum Mounting Surface Thickness: 34mm (Metric) / 1 5/16 inch
(Imperial)
Product Usage Instructions:
Tools Required:
- Pencil
- Electric Drill
- 7mm Spanner *or adjustable spanner
- 5.0mm Drillbit *if fixing from below
- 2.5mm Drillbit *if fixing from above
- 16mm Holesaw
- Socket Driver
Fixings List:
- 4x No.8 Countersunk Self-tapping Screw
- 4x M4x10mm Countersunk Screw
- 4x M4 Wing Nut
Assembly Steps:
A. Fixing from Below:
- Mark drill hole locations using Mount Washer.
- Drill holes with specified drill size.
- Screw Socket screws into the Wallmount.
- Secure the arm to the surface using Locking Nuts.
B. Fixing from Above:
- Mark drill hole locations on the Mount Plate.
- Drill holes using specified drill sizes.
- Attach the Cover to the Wallmount.
*Always tighten screws using hand tools to avoid damaging your
Bouncepad.
Mounting Tablet:
-
Clean the back of the tablet with the provided wipe and let it
dry completely. -
Remove the Mounting Plate adhesive backing.
-
Attach the Mounting Plate level and centrally to the tablet
back.
Frequently Asked Questions (FAQ):
Q: Can I use electric tools to tighten the screws?
A: It is recommended to tighten screws using hand tools to
prevent damage to your Bouncepad.
Q: What do I do if I receive additional fixings in the
kit?
A: Additional fixings may be included due to the modular nature
of our product range, and they can be used as needed during
assembly.
“`
Core Wallmount
Assembly Instructions
Tools Required:
Pencil
Electric Drill
7mm Spanner *or adjustable spanner
5.0mm Drillbit *if fixing from below
2.5mm Drillbit *if fixing from above
16mm Holesaw
*if routing the tablet cable through your mounting surface
Socket Driver
Sheet Code: BP-IM-083_REV0
Release Date: 13/08/2024
Copyright 2024 Spotspot Ltd. (T/A Bouncepad) all rights reserved.
Confidential, no part of this publication may be reproduced or transmitted in
any form without the written permission of the copyright holder.
Flat Cable
Fixings Kit
Tablet Mounting Plate
Wallmount Arm
Surface Mounting Kit
Shell
In the Box
4x No.8 Countersunk Self tapping
Screw
4x M4x10mm Countersunk
Screw
4x M4 Wing Nut
2x 3mm x 6mm Pan Head Screws
4x M4x40mm Socketset screw
4x M4x16mm Buttonhead
screw
1x T20 Pin Torx Driver Bit
1x Cable Clamp
4x M3x10mm Countersunk
Screw
1x Mount Washer
1x Case Washer
1x T10 Pin Torx Allen Key
Maximum Mounting surface thickness :
8x M4 Split Washer
Metric
25 1x Cleaningmm
4x M4
Wipe
Locking Nut
Imperial
1″
Fixings List
- Due to the modular nature of our product range you may receive additional fixings in the fixings kit
Mount Washer
Maximum Mounting surface thickness : Metric Imperial
25mm 1″
A Follow steps A if “Fixing from below”.
Ø5.0mm Drillbit
Top
*Bouncepad accepts zero responsibility for damage caused due to incorrect assembly methods.
Minimum Mounting surface thickness : Metric Imperial
34mm 1 5/16″
B Follow steps B if “Fixing from Above”.
4x Ø5.0mm
1x Ø16.0mm
Ø16.0mm Holesaw
Using the Mount washer,
A1 mark the drill hole locations as shown.
A2 Drill each hole – using the specified drill size.
M4x40mm Socketset
screw
Mount Washer M4 Split washer M4 Locking Nut
Mount Plate
Tighten screw(s) using hand tools, using electric tools may damage your
Bouncepad.
Top
7mm Spanner
Tighten screw(s) using hand tools, using electric tools may damage your
Bouncepad.
Mount Washer M4 Split washer M4 Wing Nut
*see overleaf
Top
Ø2.5mm Drillbit
4x Ø2.5mm 1x Ø16.0mm
Ø16.0mm Holesaw
Locate & screw the
A3 Socket screws into the Wallmount as shown.
Secure the arm to the
A4 surface. Locking Nuts offer higher security.
A5 Go to step 1.
Using the Mount
B1 Plate, mark the drill hole locations as shown.
Drill each hole –
B2 using the specified drill sizes.
Mount Plate Cover
M4x10mm Countersunk
Screw
Top
Tighten screw(s) using hand tools, using electric tools may damage your
Bouncepad.
No.8 Countersunk, Self
tapping Screw
Top
Locate the
B3 Cover to the Wallmount.
B4 Join the Wallmount & Mount Plate in the orientation shown.
Tighten screw(s) using hand tools, using electric tools may damage your
Bouncepad.
Secure the Wallmount to
B5 the surface with the 4x countersunk fixings.
Adhere the Mount Cover
B6 onto the Mount Plate with the adhesive tabs.
Tighten screw(s) using hand tools, using electric tools may damage your Bouncepad.
B7 Go to step 1.
T20 Pin Torx Driver Bit M4x16mm
Buttonhead screw M4 Split Washer Case Washer
Locate & attach the Shell
1 to the Wallmount in the correct orientation.
*Before attaching the Mounting Plate, fully clean the back of the tablet with the provided wipe and allow it to fully dry.
FoLraonpdtismcaalpaedhteasbiolne,tporerisesnfitramtliyoannd leave for 72hrs in
a 20°C environment before use. Do not reposition. Do not use prior to the
72hrs.
Portrait tablet orientation
Landscape
Portrait
Remove the Mounting Plate adhesive
2 backing. Attach level & centrally to the Tablet back as shown.
Attach the Flat Cable
3 to the Tablet with the U-Bend Head.
2x 3mmx6mm Pan Head Screws
Cable Clamp
Top Fixing Cover
T10 Pin Torx Allen Key
T10 Pin Torx Allen Key
Secure the Flat Cable to the
4 Mounting Plate with the Cable Clamp as shown.
Remove the Fixing Covers. Feed
5 the Flat Cable into the assembly & locate the Tablet in the chosen
orientation.
4x M3x10mm Countersunk
Screw Bottom Fixing Cover
Secure the Tablet to the
6 Shell & attach the Fixing Covers as shown.
Connect tablet
7 to power & installation is now complete.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>