bouncepad FS-B4-FE7-MG Floorstanding Tablet Security Enclosure Instruction Manual
- June 1, 2024
- bouncepad
Table of Contents
bouncepad FS-B4-FE7-MG Floorstanding Tablet Security Enclosure
Product Information
- Product: Floorstanding
- Sheet Code: BP-IM-047_REV4
- Release Date: 10/04/2024
- Copyright 2024 Spotspot Ltd. (T/A Bouncepad) all rights reserved.
Product Usage Instructions
Assembly Instructions:
Tools Required:
- Socket Driver 10mm Spanner *or adjustable spanner
- Pair of Keys
- 1x Case Washer
- 4x M4 Split Washer
- 4x M6 Split Washer
- 4x M4x20mm 1x T20 Pin Buttonhead Torx Driver Bit screw
- 4x M6x25mm Countersunk screw
Step-by-Step Assembly:
- Orientate, locate and secure the Floorstanding Pole to the Floorstanding Base. Ensure all fixings are installed correctly.
- Locate the Floorstanding Cover over the Floorstanding Pole.
- Secure the Case onto the Mounting Arm. Tighten by hand.
- Install Tablet Supports, Corner Pieces, and Cable Clip.
- Unlock & remove the Faceplate from the Bouncepad Case.
- Feed the tablet power cable through the Case & Floorstanding Pole.
- Install the Tablet Setup Kit specific per device & case.
- Install the tablet into the Case & connect to power.
- Locate and lock the Faceplate to the Case.
- Connect the tablet power cable to its main power source.
- If installing a battery pack, connect the tablet cable and locate the pack into the Floorstanding Base.
- Locate and fit the Floorstanding Rubber Collar.
Installation Complete:
Your installation is now complete. Enjoy using your Floorstanding product!
Frequently Asked Questions
Q: Can I use electric tools for assembly?
A: No, using electric tools may damage your Bouncepad. Please tighten the screws using hand tools.
Q: Can I purchase additional keys for the product?
A: Yes, we recommend recording the key number provided so you can purchase additional keys in the future.
Q: What battery pack is recommended for use with this product?
A: The product is designed to support the Anker PowerCore 10000mAh battery pack, which is not provided with the product.
In the Box
Fixings List
Due to the modular nature of our product range, you may receive additional fixings in the fixings kit
Tools Required
- Socket Driver
- 10mm Spanner *or adjustable spanner
Assembly Instructions
- Orientate, locate and secure the Floorstanding Pole to the Floorstanding Base as shown. Ensure that all fixings are installed correctly.
- Locate the Floorstanding Cover over the Floorstanding Pole.
- Locate and secure the Case onto the Mounting Arm as shown. Tighten by hand.
- Unlock & remove the Faceplate from the Bouncepad Case.
- Feed the tablet power cable through the Case & Floorstanding Pole.
- Install the Tablet Setup Kit. Each kit is specific per device & case.
- Install the tablet into the Case & connect to power.
- Locate and lock the Faceplate to the Case.
- 9.1 Connect the tablet power cable to its main power source.
- 9.2 If installing a battery pack, connect the tablet cable and locate the pack into the Floorstanding Base.
- 9.2 If installing a battery pack, connect the tablet cable and locate the pack into the Floorstanding Base.
- With the Floorstanding Cover on the ground, locate and fit the Floorstanding Rubber Collar.
- Use a Kensington® Microsaver product to tether to a secure object. (refer to your Kensington® instructions for full details)
- Installation is now complete.
Copyright 2024 Spotspot Ltd. (T/A Bouncepad) all rights reserved. Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder.
- Sheet Code: BP-IM-047_REV4
- Release Date: 10/04/2024