bouncepad FBR-W1-M4-MN Floorstanding with Brother Printer Mount Tablet Security Enclosure Instruction Manual

June 1, 2024
bouncepad

bouncepad-LOGO

bouncepad FBR-W1-M4-MN Floorstanding with Brother Printer Mount Tablet

Security Enclosure

bouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-
Security-Enclosure-PRODUCT

Product Specifications

  • Product Name: Floorstanding with Brother Printer Mount
  • Manufacturer: Spotspot Ltd. (T/A Bouncepad)
  • Release Date: 26/03/2024
  • Copyright: 2016 Spotspot Ltd. (T/A Bouncepad), all rights reserved

Product Usage Instructions

Assembly Instructions

  • Socket Driver
  • 10mm Spanner or adjustable spanner
  • Pair of Keys
  • T20 Pin Buttonhead Torx Driver Bit
  • T10 Pin Torx Allen Key
  • PZ3 Pozi Driver Bit

Assembly Steps

  1. Orientate, locate, and secure the Floorstanding Pole to the Floorstanding Base.
  2. Place the Floorstanding Cover over the Floorstanding Pole.
  3. Remove Neck-Ring using the T20 driver bit and Socket Driver.
  4. Feed the printer’s power cable through the Floorstanding Pole.
  5. Attach the printer to the Printer Mount using M3x10mm Screws.
  6. Feed power cable through Printer Mount and plug into Printer.
  7. Re-attach Neck-Ring.
  8. Pull the cable back to remove any slack near the Printer Mount.
  9. Locate and secure the Case onto the Mounting Arm. Tighten by hand.
  10. Unlock & remove the Faceplate from the Bouncepad Case.
  11. Feed the tablet power cable through the Case & Floorstanding Pole.
  12. Install the Tablet Setup Kit specific to your device & case.
  13. Install the tablet into the Case & connect to power.
  14. Lock the Faceplate to the Case.
  15. If using a battery pack, connect the tablet cable and place the pack into the Floorstanding Base.
  16. Place the Floorstanding Rubber Collar on the ground.
  17. Record key number for future key purchases.
  18. Installation is now complete.

Frequently Asked Questions (FAQ)

Q: What type of printer is compatible with the Brother Printer Mount?

  • A: The Brother Printer Mount is designed for Brother QL-820WNB printers. Please note that the printer is not provided with the mount.

Q: Can I use electric tools for tightening screws during assembly?

  • A: It is recommended to tighten screws using hand tools, as using electric tools may damage your Bouncepad.

Q: What type of battery pack is recommended for use with this product?

  • A: The product is designed to support the Anker PowerCore 10000mAh battery pack, which is not provided with the product.

Floorstanding with Brother Printer Mount

Tools Required:

  • Socket Driver
  • 10mm Spanner *or adjustable spanner
  • Sheet Code: BP-IM-057_REV2
  • Release Date: 26/03/2024
  • Copyright 2016 Spotspot Ltd. (T/A Bouncepad) all rights reserved.
  • Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder.

Assembly Instructions

bouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-
Security-Enclosure-FIG-1 bouncepad-FBR-W1-M4-MN-Floorstanding-with-
Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-2

  1. Orientate, locate, and secure the Floorstanding Pole to the Floorstanding Base as shown. Ensure that all fixings are installed correctly.
  2. Locate the Floorstanding Cover over the Floorstanding Pole.bouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-3
  3. Remove Neck-Ring using the T20 driver bit and Socket Driver
  4. Feed the printer’s power cable through the Floorstanding Pole
  5. Attach the printer to the Printer Mount using M3x10mm Screwsbouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-4
  6. Feed power cable through Printer Mount and plug into Printer
  7. Re-attach Neck-Ring
  8. Pull the cable back to remove any slack near the Printer Mountbouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-5
  9. Locate and secure the Case onto the Mounting Arm as shown. Tighten by hand.
  10. Unlock & remove the Faceplate from the Bouncepad Case.
  11. Feed the tablet power cable through the Case & Floorstanding Pole.bouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-6
  12. Install the Tablet Setup Kit. Each kit is specific per device & case.
  13. Install the tablet into the Case & connect to power.
  14. Locate and lock the Faceplate to the Case. bouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-7
  15. Connect the tablet power cable to its main power source.
  16. If installing a battery pack, connect the tablet cable and locate the pack into the Floorstanding Base.
  17. With the Floorstanding Cover on the ground, locate and fit the Floorstanding Rubber Collar.bouncepad-FBR-W1-M4-MN-Floorstanding-with-Brother-Printer-Mount-Tablet-Security-Enclosure-FIG-8
  18. Use a Kensington® Microsaver product to tether to a secure object. (refer to your Kensington® instructions for full details)
  19. Installation is now complete.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

bouncepad User Manuals

Related Manuals