KOZY HEAT Carlton Series Direct Vent Fireplaces Instructions
- June 10, 2024
- Kozy Heat
Table of Contents
**KOZY HEAT Carlton Series Direct Vent Fireplaces
**
Introduction
Please leave these reference guides at the installation location until the installation is finished. See owners manual for full installation and finishing instructions before making final decisions as information is subject to change.
Specifications (all measurements are in inches)
Model
|
BTU
| Height| Front Width| Back Width| Depth| Glass
Viewing Area
---|---|---|---|---|---|---
Actual| Framing| Actual| Framing| Actual| Framing| Actual| Framing
CAR‐39
| 40,000 (NG)
41,000 (LP)
|
34‐1/2
|
44‐1/2
|
38‐3/4
|
39‐3/4
|
19‐15/16
|
39‐3/4
|
22
|
22‐1/2
|
28‐1/8 x 32‐7/16
CAR‐46| 45,000| 36| 46| 45‐3/4| 46‐1/4| 22‐38| 45‐3/4| 21‐1/2| 22| 27‐1/2 x 39‐7/16
Framing Opening
| Dimension | CAR‐39 | CAR‐46 |
|---|---|---|
| A | 44‐1/2 | 46 |
| B | 39‐3/4 | 46‐1/2 |
| C | 22 | 21‐1/2 |
| Dimension | CAR‐39 | CAR‐46 |
|---|---|---|
| D | 22 | 21‐1/2 |
| E | 39‐1/4 | 46‐1/4 |
| F | 62‐5/8 | 64‐3/4 |
| G | 39‐3/4 | 46‐1/4 |
| H | 12‐9/16 | 13‐5/16 |
| I | 44‐5/16 | 45‐3/4 |
| J | 31‐5/16 | 32‐3/8 |
Finishing Clearances
| Dimension | CAR‐39 | CAR‐46 |
|---|---|---|
| K | 39-3/4 | 46‐1/2 |
| L | 10 | 10 |
Mantel Clearances
| Dimension | CAR‐39 | CAR‐46 | Dimension | CAR‐39 | CAR‐46 |
|---|---|---|---|---|---|
| M | 10 | 10 | O | 16 | 16 |
| N | 14 | 14 | P | 18 | 18 |
Finish Trim Kit
Important!
If you are finishing around the fireplace with tile or stone make sure that
you install the Finishing Trim Kit at the framing stage.
The trim kit allows for your finishing board and your tile/stone to finish up
against, creating a shadowbox for the face to sit inside.
Do not use with RSF fronts, all other fronts apply.
Horizontal Termination Framing
| Dimension | CAR‐39 (NG) | CAR‐46 (NG) |
|---|---|---|
| R | 22 | 21 |
| S | 46‐1/4 | 47‐3/4 |
Dimension| CAR‐39
(LP)
| CAR‐46
(LP)
---|---|---
T| 22| 21
U| 52‐1/4| 53‐3/4
Dimension| CAR‐39
(NG/LP)
| CAR‐46
(NG/LP)
---|---|---
V| 22| 21‐1/2
W| 51‐1/8| 52‐5/8
Horizontal Venting Minimum Requirements
Note specific model number and gas type minimums
| Requirement | CAR‐39 | CAR‐46 |
|---|---|---|
| (NG) Vertical Min | 9 + 90o Elbow | 9 + 90o Elbow |
| (NG) Horizontal Min | 6 | 6 |
| (NG) Horizontal Max | 10 ft. | 10 ft. |
Consult venting chart in manual for all options above minimum requirements
| Requirement | CAR‐39 | CAR‐46 |
|---|---|---|
| (LP) Vertical Min | 12 + 90o Elbow | 12 + 90o Elbow |
| (LP) Horizontal Min | 6 | 6 |
| (LP) Horizontal Max | 4 ft. | 4 ft. |
CORNER VENTING|
---|---
Requirement| CAR‐46 (NG ONLY)
Vertical Min| 6 + 90o Elbow
Horizontal Min| 6
Horizontal Max| CAP
CORNER VENTING|
---|---
Requirement| CAR‐39| CAR‐46 (LP ONLY)
(NG/LP) Vertical Min| 12 + 90o
Elbow
| 12 + 90o Elbow
(NG) Vertical Min| 12 + 90o
Elbow
| 12 + 90o Elbow
(LP) Horizontal Min| 6| 6
(LP) Horizontal Max| CAP| CAP
Heat Shield Requirements
The vertical vent heat shield must be installed for EVERY type of venting application. The horizontal vent heat shield must be installed when incorporating minimum horizontal venting and is positioned according to the gas type.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>