neno Bambino Electronic Nanny User Manual
- September 11, 2024
- neno
Table of Contents
**neno Bambino Electronic Nanny User Manual
**
Thank you for purchasing our Neno Bambino baby monitor. With this device you
can continuously monitor your child’s sleep or play in another room.
Communication between the transmitter and receiver takes place via radio waves
with a maximum distance of 300m (in open spaces). The digital connection
ensures interference-free data transmission. The camera is equipped with IR
LEDs that switch on automatically when light levels are insufficient. The two-
way intercom allows you to talk to your child. You can also check the
temperature in your child’s room at any time thanks to the built-in sensor.
The monitor has a built-in battery so you can always have it with you.
Please read this user manual carefully before using the product.
CAUTION: Leave the charging cable in a safe place (position) out of the
reach of the child. Failure to do so may put the child at risk of suffocation
or other dangerous situations (e.g. electric shock).
BEFORE USE
The Neno Bambino electronic baby monitor with all relevant EMF standards and
is safe to use provided it is used as described in the user manual. In
particular, pay attention to the following points:
- Installation of the device must be carried out by an adult. Keep small parts away from children during installation.
- This product is not a toy. Do not allow children to play with the device.
- The camera cannot fully replace adult supervision.
- Do not place the camera or cables in the middle of a cot or within reach of children. Leave a minimum distance of 1 m.
- Keep cables out of the reach of children.
- Do not keep the baby monitor near water or heat sources.
- Use only the original parts supplied with the product.
- Do not touch the contacts of the power socket with sharp or metallic objects.
- Do not attempt to open the unit’s covers.
ATTENTION: The range of the device is affected by external factors (e.g. walls, high-voltage lines, other electrical equipment), so the actual range may be much lower than specified.
CONTENTS OF THE KIT
- Monitor
- Camera
- Power supply x2
- Flexible handle
- Operating instructions
PRODUCT DESCRIPTION
A. RECEIVER/MONITOR SEE FIG. A
- Sound level indicator
- Monitor charge indicator
- Zoom button
- MENU and back button
- Confirmation button
- Control buttons (menu navigation, brightness)
- Two-way communication button
- Lullabies
- Microphone
- Power supply diode
- Screen
- Loudspeaker
- Volume keys
- Switch
- USB-C charging port
- Reset button
B. TRANSMITTER/CAMERA SEE FIG. B
- Camera lens
- Light sensor
- Infrared LEDs
- Power indicator
- Microphone
- Reset/pause button
- Loudspeaker
- USB-C charging socket
- Temperature sensor
INSTALLATION OF THE DEVICE
Before mounting the camera, check the preview to ensure that the frame is
appropriate. Check for proper signal reception. If necessary, move the camera
to get a better signal.
- Connect the power supply to the camera and power source.
- Connect the power cable to the monitor and power source, then switch on the screen. It is recommended to fully charge the battery before first use.
- Place the camera in a convenient location. The camera can be placed or mounted on a flexible bracket. Disconnect the power supply before mounting and reconnect after correct installation.
- Assembly methods:
Method 1: Place the camera on a flat, dry surface. SEE FIG. C
Method 2: A flexible bracket is included with the product, with which you mount the camera in the location of your choice. Wind the bracket and then screw the camera onto the thread. Check that the camera is correctly attached and will not fall out of the thread. SEE FIG. D
CAUTION: Ensure that the camera and power cable are mounted out of the reach of the child and do not create a hazard. Poor mounting can lead, for example, to a child being strangled by the cable.
SCREEN: ICONS AND FUNCTIONS SEE FIG. E
- Signal strength indicator
- Indicator for muted sounds
- Lullaby playback
- Viewing indicator for selected camera
- Approximation level
- VOX mode enabled
- Temperature at the camera site
- Night mode indicator
- Active alarm
- Battery indicator
- Two-way communication function enabled
- VOX settings
- Camera settings
- Lullaby settings
- Screen zoom settings
- Temperature/alarm settings
GETTING STARTED – PAIRING THE CAMERA WITH THE RECEIVER
The monitor and camera are paired with each other. They do not need to be
paired with each other again unless there has been a loss of connection.
In this case, follow the instructions:
- Press the MENU button to enter the main menu.
- Select CAMERA SETTINGS (FIG. E13), select the camera icon with the plus sign and press “OK”.
- Select the number where you want your camera to be located and press “OK”.
- Press and hold the pairing button on the camera for 3 seconds within 60 seconds.
- After successful pairing, the receiver will return to the home screen and display the image from the paired camera.
USE OF THE DEVICE
A. ZOOM
While viewing the camera, press the “Zoom” button (FIG. A3) on the monitor to
zoom in on the preview image two or four times. Pressing the button again will
increase the magnification and another will return the image to its initial
state.
B. LULLABIES
While viewing the camera, press the “Lullabies”(FIG A6) button on the monitor
to play them through the camera’s built-in speaker. A looping playback will
take place. The next click of the same button changes the lullaby to the next
one. The lullabies will be switched off by clicking again while the 6th (last)
lullaby is playing.
C. TWO-WAY COMMUNICATION
While viewing the camera, press and hold the “Two-way communication” button
(FIG. A7) on the monitor while speaking. The corresponding symbol will appear
at the top of the screen.
D. VOLUME SETTINGS
Use the volume keys (FIG. A13) to select your preferred volume. Its current
level will be displayed in the centre of the screen.
E. DISPLAY BRIGHTNESS SETTINGS
Use the control buttons (FIG. A 6) right and left to adjust the preferred
brightness. Its current level is displayed in the centre of the screen.
F. MAIN MENU
Press the “MENU” button (FIG. A 4) to enter the main menu, which contains 5
items:
-
VOX
Press the “MENU” button to enter VOX mode. In this mode, the screen automatically switches off to save power. The screen reactivates automatically when sound is detected at the camera site. There are 4 modes: off, sensitivity: low, medium and high. -
Camera
Press the “MENU” button to access the camera settings.
If a camera is paired you can disconnect it by selecting the camera icon with a minus sign and then the number of the camera you want to disconnect.
If your camera is not connected to the receiver, select the camera icon with a plus. Then select the number where you want your camera to be located. Press and hold the pairing button on the camera for 3 seconds within 60 seconds.
If you have more than one camera connected, you can choose to automatically change the preview at a specific time interval. There are 4 modes available: off, every 15, 30 or 60 seconds. -
Lullabies
Press the “MENU” button to access the lullaby settings.
Use the controls to select the lullaby you want to play, the possible option to repeat or loop the song, and the volume. -
Screen zooming
Press the “MENU” button to access the zoom settings.
Use the control buttons to select the screen zoom, there are 2 options to choose from: 2x and 4x. -
Temperature/alarm settings
Press the “MENU” button to access the temperature/alarm settings.
Press the alarm icon to select its volume.
Use the control buttons to select the temperature unit and set the minimum and maximum values at the camera site. If the temperature exceeds the set value, the unit will beep.
Use the controls to set the feeding reminder, 3 options are available: off, every 30 minutes, 1 hour or 2 hours.
SPECIFICATION
Display: 2.8 inches
Camera and monitor input: DC 5V/1A
Input voltage for power supplies: 220-240V 50-60 Hz
Signal range: up to 300m (outdoor), up to 50m (indoor)
Monitor resolution: 320x240px
Camera resolution: 640x480px
Viewing angle of the camera: 90°
Built-in battery (monitor): 2600mAh
Frequency range: 2412-2469 MHz
Night mode: up to 5m
Operating temperature: -10-50 °C
Light sensor: Yes
Temperature sensor: Yes
Maximum RF power emitted in the frequency range 2412-2469 MHz: camera:
9.49 dBm, monitor: 9.526 dBm
Dimensions: monitor 11.9x8x3.7 cm, camera 6.5×6.5×10.6 cm
Weight: monitor 125g, camera 93g
WARRANTY CARD
The product comes with a 24-month guarantee.
Warranty conditions can be found at: https://neno.pl/gwarancja
Details, contact and service address can be found at: https://neno.pl/kontakt
Specifications and contents are subject to change without notice. We apologise
for any inconvenience.
KGK Trend declares that the Neno Bambino device complies with the essential
requirements of Directive 2014/53/EU. The full declaration can be found at the
following link: https://neno.pl/download/DOC/deklaracja-CE-Neno-
Bambino.pdf
The crossed out trash can symbol indicates that unusable electrical or
electronic devices, its accessories (such as power supplies, cords) or
components (for example batteries, if included) cannot be disposed of
alongside with household waste. In order to dispose of the devices or its
components (for example, batteries) deliver the device to the collection
point, where it will be accepted free of charge. Disposal is subject to the
recast version of the WEEE Directive (2012/19/ EU) and the Directive on
batteries and accumulators (2006/66/ EC). Proper disposal of the device
prevents degradation of the natural environment. Information about the
collection points of the facilities is issued by the competent local
authorities. Incorrect disposal of waste is subject to penalties provided for
by the law in force in the given area.
Producent : KGK TREND Sp. z o.o. ul. Ujastek 5b, 31-752 Kraków, Polska. Wyprodukowano w PRC
Manufacturer :
KGK TREND Sp. z o. o. Ujastek 5b, 31-752 Cracow, Poland. Made in PRC
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>