neno Titto Silicone Bedside Lamp for Children User Manual
- June 3, 2024
- neno
Table of Contents
neno Titto Silicone Bedside Lamp for Children User Manual
Dear Customer,
Thank you for purchasing the Neno Titto LED lamp. It is used to illuminate a
room and is intended for domestic use. Please, read the instructions before
using the device.
SAFETY MEASURES
- Read the user manual carefully before use, and keep it as a reference for the future.
- Follow the instructions carefully when using the device.
- Clean the device with a dry cloth. Moisture can damage the inside of the device.
- Make sure that the power cord is routed so that it does not constitute a hazard to people walking by.
- The device is for indoor use only.
- Do not place the device near water, radiators, hot-air vents, cookers, or other sources of heat or moisture.
- Keep the power cord out of reach of a child.
- The product is not a toy. Do not allow children to play with the appliance.
- If the product is damaged, do not disassemble it yourself. Contact an authorized service center.
THE SET CONTAINS
- Bunny shape lamp, USB cable, Remote control, User manual
USING THE DEVICE
- Connect the lamp to the USB socket in a wall charger, power bank, computer, or laptop using the included USB cable. Make sure the cord is out of the reach of your child. Make sure that the power source meets the parameters of the lamp (5V / 0.5A). Using an overly powerful power source may lead to the fire of the device or other hazardous situations.
See Fig. 1.
- Enable / disable
- Dimming
- Brightening
- Red
- Cold white
- Warm white
- Green
- Blue
- Orange
- Violet
- Gradual change of 7 colors
- Cyan
- Automatic off mode after 60 min.
- Automatic off mode after 15 min.
- Automatic off mode after 30 min.
On the left side of the charging socket, there is a diode that will indicate the battery charge status. The red light will be on when charging and will turn off when the battery is fully charged. 3. You can control the lamp by touching the bunny’s tail and body or using the remote control included in the set.
LIGHT CONTROL WITHOUT USE OF A REMOTE CONTROL
- To turn on the lamp, press the tail of the bunny.
- To change light brightness or color, press and hold the tail. The lamp will start to change brightness, and when it reaches the lowest intensity it will change from cold to warm color.
- Another press on the tail will make the light switch into RGB mode. In this mode, the colors will begin to change automatically. You can also press the bunny’s body when you want the lamp to light only in this color. Another push on the bunny’s body will make the colors will start to change again.
- Another press on the tail will turn the light off.
LAMP CONTROL BY A REMOTE CONTROL
- Press the on / off button to turn the lamp on or off
- Press the “-” button to dim the lamp
- Press “+” button to brighten the lamp
- Press one of the 8 buttons to select a light’s color or a button with automatic RGB color switching.
- Press one of the “15min”, “30min” or “60min” buttons so that the lamp automatically turns off after a certain time. When one of the buttons is pressed, the light will dim and brighten, indicating that the time has been successfully set. To disable this mode, press the on / off button.
SPECIFICATION
- Material: silicone / ABS / PC
- Battery: 1200mAh allowing to use the lamp up to 100h with minimum light intensity and up to 8h with maximum light intensity.
- Input: DC5V 0.5A
- Power: 0.2-1.5W
- Color of light: warm light 3000K, white light 6500K + RGB color
- Dimensions: 147 x 90 x 98 mm
- Weight: 164g
- Charging time approx. 4.5 hours.
WARRANTY CARD
The product is covered by a 24-month warranty. The warranty conditions can be
found at: https://neno.pl/gwarancja
Details, contact and service address can be found at:
https://neno.pl/kontakt
Specifications and kit contents are subject to change without notice. We apologise for any inconvenience.
Producer: KGK Trade sp. z o.o.
Ujastek 5B 31-752 Cracow, Poland
Made in P.R.C.
The crossed out trash can symbol indicates that unusable electrical or
electronic devices, its accessories (such as power supplies, cords) or
components (for example batteries, if included) cannot be disposed of
alongside with household waste. In order to dispose of the devices or its
components (for example, batteries) deliver the device to the collection
point, where it will be accepted free of charge. Disposal is subject to the
recast version of the WEEE Directive (2012/19 / EU) and the Directive on
batteries and accumulators (2006/66 / EC). Proper disposal of the device
prevents degradation of the natural environment. Information about the
collection points of the facilities is issued by the competent local
authorities. Incorrect disposal of waste is subject to penalties provided for
by the law in force in the given area.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>