neno 2103505 300ml Baby Bottle User Manual

neno 2103505 300ml Baby Bottle

Dear Customer,
The Neno Bottle 300 product that you have purchased is a baby bottle with a rubber teat, used to feed babies or express breast milk with the use of any Neno brand breast pump.

Please read the instructions before using the device

SAFETY MEASURES

1. Do not allow your child to use this product without adult supervision.
2. Do not allow your child t play with the bottle or run around when holding it.
3. Never use the bottle as a substitute for a pacifier.
4. Always check the temperature of the bottle before feeding your child.
5. Keep all elements of the device out of reach of children.
6. Wash the product before first use. Before each use, check the product’s condition carefully and stretch the teat in all directions with your fingers. Discard the teat when you notice signs of damage or wear. Do not leave the teat in sunny or hot places. Do not soak it in sterilizing agents for longer than it is recommended, as they can damage the material.
7. Long and uninterrupted suction of food by the child may cause tooth decay.
8. Do not place the product in a preheated oven.
9. Before frst use, put the teats in boiling water for 5 minutes. Clean before each use.
10. Do not place the bottle in the microwave oven. Do not use microwave waves to heat the contents of the bottle.
11. Do not wash the product ina dishwasher.
12. The expressed milk can be stored in a bottle in the refrigerator for up to 48 hours or for up to 3 months in the freezer. Never re-freeze milk and do not add freshly expressed milk toa previously frozen milk.
13. Do not use abrasive or antibacterial agents when cleaning the product. Do not place parts of the product directly on surfaces that have been cleaned using antibacterial agents.
14. Overuse of cleaning agents may cause the plastic to crack. If there are visible cracks on the bottle or teat, discard it immediately.
15. Sterilization and high temperature can lead to distortion of the rubber teat and make the bottle and teat not fit each other.
16. Cooking a bottle and teat in hard water may cause residue.

PACKAGE COMPONENTS

1. Bottle
2. Teat size L, 6m+
3. Nut
4. Peg
5. Weighted silicone straw
6. Cleaning brush
7. Handle
8. Plastic needle

The suction process is an important part of your baby’s development, which is why when feeding your baby with a bottle, you need to make sure that it can actively suck food without a problem.

ASSEMBLY

Apply the bottle cap so that the teat is held upright. To remove the cap, put your hand on it, placing your thumb in the recess. It is easier to put on the teat by moving it sideways, instead of pulling it through the opening in a straight line. Drag the teat through the opening until the bottom part is in line with the fixing ring.

CLEANING

Before first use, disassemble the bottle, clean the individual parts thoroughly, and sterilize them with a bottle sterilizer or boiling water. After each use of the product, disassemble it, wash the parts in warm water and dish soap, and rinse afterward. Before using sterilized items, wash your hands and the surfaces on which these items will be placed.

To clean the straw, use the brush included in the set. Put the brush in the straw and drag it through the inside several times to clean it thoroughly. If the cavity of the weighted straw is logged, use the plastic needle included in the set to clear up the straw.

MAINTENANCE

Before first use, put the bottle in boiling water for 5 minutes. Before each use, check the condition of the product carefully and stretch the teat in all directions with your hangers. Discard the teat when you notice signs of damage or wear. Do not leave the teat in sunny or hot areas, and do not soak it in sterilizing agents for longer than is recommended, to avoid damage. Due to hygiene concerns, it is recommended to replace the teats every 3 months. Store the treats in a dry, closed container. Do not leave them in sunny areas. Do not soak the teats in sterilizing solution for longer than you should, this may cause damage to the material the teats are made out of. Do not place the product in a preheated oven. Do not use the bottle if there are any cracks on it. Do not allow children to use the bottle without adult supervision.

SPECIFICATION

1. Anti-colic valve
2. Material: silicone
3. Doesn’t contain BPA
4. A useful scale is drawn on the bottle
5. Dimensions: Ø6,5x12x19 cm
6. Weight: 121g
7. Bottle capacity: 300 ml

WARRANTY CARD

The product is covered by a 24-month warranty. The terms of the guarantee can be found at: https://neno.pl/gwarancja.

Details, contact and website address can be found at: https://neno.pl/kontakt.

Specifications and contents of the kit are subject to change without notice. We apologize for any inconvenience.

Manufactured for:
KGK Trade sp. z o.0. sp. k. Ujastek 5b, 31-752 Cracow Polska

www.neno.pl
inspired by Children,
designed by Parents.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>