m-e Funk-Gong FG-6.2 Doorbell Door Chime Instruction Manual

m-e Funk-Gong FG-6.2 Doorbell Door Chime

Thank you for purchasing the wireless bell FG-6.

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND KEEP THEM FOR POSSIBLE LATER USE!

No cables are necessary for this wireless doorbell. If the bell button is pressed a signal is sent to the bell unit, which activates the bell. The operating range is up to 200 metres, depending on the line of sight. The range of the radio signal is, however, reduced if the signal needs to be transmitted through walls or ceilings. Metal doorframes and reinforced UPVC doorframes also reduce the operating range.

BELL BUTTON UNIT

(Figure 1)

1 x 3 volt lithium battery (CR2450) is already installed. Please remove the battery contact strip if necessary. The bell button is ready for immediate use.

Mounting
To mount the unit please break out the two pre-drilled holes and use the back as a template to mark the mounting position. Drill the holes and attach the mounting plate to the wall with the screws and dowels (included). Replace the front section.

Attention – Do not break the holes out if you do not want to mount the unit using screws as this will impede the unit’s water resistance.

INITIAL STARTUP

Setting up the transmitter

1. Insert the battery in the transmitter.
2. Plug the receiver into the socket, or insert the batteries in the receiver. The receiver should acknowledge this with two beeps.
3. Press the bell button on the transmitter.
4. The receiver plays a melody and the system is ready for use.

Setting the ring tone
Ring tone selection is carried out using the small, black button (2) in the bell button unit that is marked with the letter ‘S’. The ring tone is set to the Westminster’ tone at the factory. If you wish to change this to one of the seven other possible tones then press the button (2) briefly until you hear a tone from the doorbell unit. Repeat this process until you hear the bell tone that you wish to use. The last tone played remains in the unit’s memory and is set.

1. Westminster
2. Ding Dong
3. Ding Dong Ding
4. Tubular-1
5. Orchestra
6. Tubular-2
7. Trumpet
8. Dog barking

MODE selector
The function (Mode) selector is located at the back of the unit.
Press the button to select the function to operate the chime unit accordingly.
The door chime will start operate at “Sound Only” function initially.
With each pressing of the MODE selector button the device will switch to the next function:

1. Sound Only: Door Chime unit will sound
2. Light Only: The Super Bright LED Light on the Door Chime unit will flash
3. Sound and Light: The Door chime will sound as well as the Super Bright LED Light flashing to maximizing attention

Setting up additional transmitters
Each receiver supports up to 4 transmitters. To set up additional transmitters, proceed as follows:

1. Press the CODE button (6) on the receiver for approx. 2 seconds, the receiver beeps once and is now in learning mode.
2. Press the bell button on the additional transmitter within 4 seconds.
3. The receiver plays a melody, the additional transmitter has been set up and the receiver returns to normal mode.
   Repeat these steps for all transmitters that need to be set up. A maximum of 4 transmitters are supported.
   Note: If the bell button on the transmitter is not pressed within 4 seconds of activating learning mode, learning mode is automatically deactivated on the receiver and this is acknowledged by a signal tone.

A.5 Changing the system code
In rare cases the signal code of your system may overlap with that of a neighbour. If so, the code(s) will need to be changed.

1. Open the transmitter and remove the battery (CR2450).
2. Wait approx. 10 seconds and reinsert the battery.
3. Unplug the receiver from the socket, or remove the batteries.
4. Wait approx. 30 seconds.
5. Plug the receiver into the socket, or insert the batteries in the receiver. The receiver should acknowledge this with two beeps.
6. Press the bell button on the transmitter.
7. The receiver plays a melody.

Any additional transmitters must also be assigned a new code and must be set up again. To do this, remove the battery (CR2450) from the transmitter for approx. 10 seconds and then perform the steps listed under “Setting up additional transmitters”.

Changing the battery
Remove the back of the casing by pressing a small slotted screwdriver against the notch on the side and lift the casing off in an upward motion (as shown in figure 1). Remove the old battery and insert one 3-volt lithium battery (CR2450). Ensure that the positive pole (+) is facing in the right direction. Replace the cover by inserting the hooks on the top of the reverse side and click it into the lower edge.

BELL UNIT (figure 2)

The bell unit is operated with 2 ‘AA’ batteries. Open the battery compartment on the back and insert the batteries in accordance with the polarity markings. The unit is now ready for use.

Set volume
There is a rotary button (4) on the reverse in the battery compartment that can be used to set the volume. Turn the button in a clockwise direction to increase volume and in an anti-clockwise direction to reduce volume.

AVAILABLE ACCESSORIES

FG-Transmitter

IMPORTANT INFORMATION

The portable doorbell is a sensitive electronic product and the following precautionary measures should always be taken:

• The bell unit should only be used in dry locations.
• Do not expose the bell unit to direct sunlight or moisture.
• If you stop using the bell button or the doorbell unit for a long period then remove the batteries and store them in a safe place.
• Do not drop either of the units and do not subject them to excessive impacts.

TROUBLE-SHOOTING & NOTES FOR USE

PROBLEM:
Bell does not ring when the bell button is pressed.

POSSIBLE CAUSES:

1. Units are outside operating range, max. 200 metres
2. Bell button and bell unit are not set to the same channel.
3. The batteries need replacing.

RECOMMENDED STEPS:

1. Mount the doorbell unit closer to the bell button unit.
2. Check the channel setting (see setting channels).
3. Replace the batteries.

PROBLEM:
Bell rings without the bell button having been pressed.

POSSIBLE CAUSE:
A similar radio product is being used in the close vicinity on the same channel.

RECOMMENDED STEPS:
Changing the channel (see setting channels).

IMPORTANT NOTE:
There are no parts in the unit that require you to maintain them; do not try to open the unit for repairs.

SPECIFICATIONS

• Bell button

  • Power:
    1 x 3 volt lithium battery CR2450 (included)

  • Power consumption:
    1.5 mA – ON / 0.001 mA – OFF

• Doorbell unit

  • Power supply: 2 x 1.5 volt mignon type ‘AA’
  • Operating range: up to 200 metres in line of sight
  • Available ring tones: 8

INFORMATION

Information regarding CE – Conformity The functionality of the unit can be affected by the influence of strong static, electrical or high frequency fields (discharging, mobile phones, radios, microwaves).

Cleaning and maintenance
Always disconnect mains-powered units from the mains supply before cleaning (disconnect the plug). The unit housing can be cleaned using a soapy soft cloth. Do not use any abrasive materials or chemicals. Remove dust build-up from ventilation slit using a brush and clean up using a vacuum deaner. Do not hold the vacuum cleaner nozzle directly against the unit.

Safety instructions
In the event of damage to the housing, connectors, power cables or isolation shielding, switch off the device immediately and disconnect from the mains power. ELECTRIC SHOCK – DANGER OF LOSS OF LIFE. (Unplug the mains connector from the socket!). Damage should be repaired immediately by a specialist!

Never carry out repairs yourself!

• The warranty will be null and void in case of damages arising from violations of these operating instructions. We are not liable for consequential damages!
• We accept no liability for material damages or injuries arising from inappropriate use or violation of the satety instructions. In such cases all warranty claims are null and void!
• Do not use this product in hospitals or other medical facilities. Although this device transmits only relatively weak radio signals, the signals may in such locations result in malfunctioning of systems critical to life. The same may apply to other areas.
• For reasons of safety and licensing (CE), unauthorised conversion and /or modification of the product is prohibited.
• Do not take the product apart! There is a danger of lethal electric shock!
• Do not leave packaging material lying about since plastic foils and pockets and polystyrene parts etc. could be lethal toys for children.
• The interior unit is suitable only for dry interior rooms (not bathrooms and other moist places). Do not allow the device to get moist or wet. There is a danger of lethal electric shock!
• In industrial institutions, the accident prevention regulations of the Association of Commercial Professional Associations for electrical installations and equipment must be observed. Please consult a specialist should you have doubts regarding the method of operation, the safety, or the connections of the device.
• Handle the product with care – it is sensitive to bumps, knocks or falls even from low heights.

Warranty

• 2 years warranty from date of purchasing, on base of correct using.
• The producer is not responsible for consequential damages which are effected directly or indirectly from this item.
• Subject to change without prior notification. In the framework of product updates and device optimization, the contents may vary from the packaging specification.

These operating instruction are published by m-e GmbH modern-electronics, An den Kolonaten 37, 26160 Bad Zwischenahn/Germany
The operating instructions reflect the current technical specifications at time of print. We reserve the right to change the technical or physical specifications.

ME-GMBH MODERN-ELECTRONICS AN DEN KOLONATEN 37 D-26160 BAD ZWISCHENAHN GERMANY
WWW.M-E.DE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>