PHYLRICH 291-04 Stilt Widespread Faucet Installation Guide
- June 17, 2024
- PHYLRICH
Table of Contents
PHYLRICH 291-04 Stilt Widespread Faucet
Specifications
- Valve Hole Diameter: 1 3/8 inches
Spout Hole Diameter: Min. 1 3/8 inches
- Drain Rim Hole Diameter: 1-1/4 inches
Product Usage Instructions
Installation Steps
- Drill a 1 3/8 inch diameter hole for the HOT & COLD valve and a minimum 1 3/8 inch diameter hole for the spout.
- Insert the spout base nipple into the center hole in the lavatory or countertop. Install the stainless washer and nut on the spout nipple and tighten.
- Install the spout tee assembly as shown in the diagram.
- Remove the top fastening nut and washer from the lavatory valve. Install the valve with the blue dot on the cold side. Insert the valve from below through the hole in the lavatory or countertop.
- Reattach the top fastening nut and washers.
- Set the valve to the proper rough-in height by adjusting the bottom fastening nut. Secure the valve by tightening the top fastening nut. Repeat for the second lavatory valve.
- Insert the pre-assembled drain rim into the basin and secure it with the provided drain nut and washer. Attach the tail tube drain onto the drain rim.
- Connect stainless steel flex lines from valve outlets to the spout tee. Ensure flex lines are not kinked. Install escutcheons onto the valves and handles onto valve stems.
- Flush hot and cold supply lines before connecting the faucet to supply lines. Connect supplies to the bottom of the lavatory valves using brass coupling nuts or flexible lines. Connect waste P-trap to the drain tail piece.
Limited Warranty Information
This product is covered by a limited warranty applicable in the United States and Canada. The mechanical warranty covers product functionality under normal conditions for a period of 10 years from the date of purchase. Ceramic disc valves are warranted for life as long as the original purchaser owns the house in which they are installed.
This Limited Warranty is expressly in lieu of any other warranties, expressed
or implied, arising by law or otherwise, including without limitation, any
implied warranty of merchantability or fitness for a particular purpose. This
Limited Warranty may not be altered, varied, or extended, except by a written
instrument executed by Phylrich. The remedy or repair or replacement as
provided under this Limited Warranty is exclusive. In no event shall the
manufacturer be liable for any consequential or incidental damages to any
person, whether or not occasioned by negligence of Phylrich, including without
limitation damages for loss of use, costs of property damage or other monetary
loss. Some states do not allow the exclusion or limitation of incidental or
consequential damages or limitations on how long an implied warranty lasts, so
the above limitations or exclusions may not apply. This warranty gives you
specific legal rights and you may also have other rights which vary from state
to state.
This warranty covers product installed in the United States and Canada.
Several types of limited warranties are applicable to decorative plumbing and
hardware products as follows.
Mechanical Warranty: This warranty covers the ability of the product to function properly under normal conditions. Our products are warrantied to the original purchaser to be free of defects in material and workmanship for a period of 10 years from the date of purchase.
Because plumbing valves have several mechanical differences due to the
function i.e. faucet valves vs. thermostatic shower valves, the following
valve warranties are established:
Ceramic disc valves are warranted for life as long as the original purchaser
owns the house in which they are installed.
Other types of valves, to include thermostatic and balance pressure shower
valves, etc. are warranted for one year from the date of purchase.
Finish Warranty: Because certain metal finishes are more durable than others
and certain applications require more durability, 4 finish warranties have
been established:
-
Certain metal finishes such as antique brass, satin nickel and satin brass are coated with an organic clear coating.
-
These coated types of finishes are warranted for 10 years from the date of shipment to the original purchaser.
-
Finishes with harder surfaces such as polished chrome, Physical Vapor Deposition (PVD) finishes and powder coated
finishes are warranted as long as the original purchaser owns the home. -
The so called “living finishes” are not warranted. These finishes have no protective coating and thus are designed to change with age and use.
-
Finishes on Drains: Because of the use and abuse of the metal surface that occurs on sink and bath drains with soap and cleaning solutions, only drains in the “B” category above warranted. This warranty is for one year from the date of purchase. Drains in the above A and C categories are not warranted.
The warranties described above are specific rights, but there may be other
rights which vary from state to state.
If you have a problem with one of our products, here is what is covered and
how you should proceed:
First of all, consult the dealer from whom you purchased the product. Please
provide proof of purchase in the form of an original invoice or receipt. If
the dealer is an authorized Phylrich dealer, he will review the problem and
contact the Phylrich customer service department on your behalf. If you cannot
contact your dealer, please e-mail our customer service at
customer.service@phylrich.com and describe the problem along with your contact
information.
The Phylrich Warranty does not assume liability for charges such as labor,
freight, removal and reinstallation or injuries resulting from a defective
product. Phylrich will repair or replace defective parts after it has been
established that the product is defective and that the parts are covered by
this warranty. Phylrich reserves the right to determine whether to repair or
replace the product under consideration.
Phylrich products must be installed in accordance with the instructions
provided with the product. Make sure your installer flushes out all debris
such as solder before final assembly. Plumber’s putty should not be used on
any decorative surface as it could harm the finish and void the warranty.
For proper maintenance do not use any abrasive cleaners, strong cleaning
solutions or polishing compunds. Usually a soft damp cloth will suffice. Non-
abrasive waxes can also be used.
FAQ
Q: Are supply lines and angle stops included with the product?
A: No, supply lines and angle stops are not included with the product.
Q: What should I do if there is a kink in the flex lines?
A: Adjust the valves and/or spout tee to eliminate any kinking in the flex lines during installation.