rf solutions DS-006-3 RF Signal Strength Meter Owner’s Manual

Table of Contents

Applications

Description

RF Signal Strength Meter is a versatile handheld test meter for checking radio signal strength or interference in a given area.
The Signal Strength Meter can both transmit and receive signals making it possible to test an installation location for suitability before installing equipment.
The Signal Strength Meter is very hard-wearing, long-lasting, and simple to use.
It has 4 selectable frequencies, changeable at the touch of a button. It also has an auto shut-off feature for battery saving.

Part Number	Description
006	Signal Strength Meter

Spot Frequencies used

The 006 has two functions

Transmit – The 006 sends out a pulsed transmission which can be received by any module on the frequency selected. Or by another 006 set to the same frequency.
Transmit power: the 006 transmits at 0dBm
Transmit timing: the 006 sends a 100ms pulse every 1 second
Transmit signal modulation: a 1KHz sine wave is modulated over the transmit signal.
Receive – when set to receive mode, the 006 displays any signals detected in the selected frequency. The receive sensitivity is shown on the front panel (as below).

Antenna

As standard, the 006 is fitted with a 433.92MHz antenna.
This should be sufficient for most applications, however, other antennas are available from the RF Solutions website for improved performance on specific frequencies.
See www.rfsolutions.co.uk for more details.

	Min	Typical	Max	Units
Supply voltage	2.2	3	3.3	V
Frequency		315.00		MHz
		433.92		MHz
		869.50		MHz
		915.00		MHz
Bandwidth		000.10		MHz
Max. RF Input		+20		dBm
RF Sensitivity	See	Sticker	Overlay	dBm
Operating Temperature	0		+50	o C
Storage Temperature	– 20		+60	o C

Q: What is the purpose of the RF Signal Strength Meter?
- A: The RF Signal Strength Meter is used for checking radio signal strength or interference in a given area, making it ideal for testing installation locations before equipment setup.
Q: How do I change frequencies on the RF Signal Strength Meter?
- A: Press the Power/Band Button to scroll through the available frequencies. The selected frequency will be indicated by the red LED.
Q: Can I extend the antenna range of the RF Signal Strength Meter?
- A: Yes, alternative antennas can be purchased from the RF Solutions website for improved performance on specific frequencies.

Simplified Declaration of Conformity (RED)

Hereby, RF Solutions Limited declares that the radio equipment type defined within this document complies with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: www.rfsolutions.co.uk.
RF Solutions Ltd. Recycling Notice
Meets the following EC Directives:
DO NOT
Discard with normal waste, please recycle.
Meets the following EC Directives:
ROHS Directive 2011/65/EU and amendment 2015/863/EU
Specifies certain limits for hazardous substances.
WEEE Directive 2012/19/EU
Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF Solutions Ltd. fulfills its WEEE obligations by membership of an approved compliance scheme.
Environment Agency producer registration number: WEE/JB0104WV.
Waste Batteries and Accumulators Directive 2006/66/EC Where batteries are fitted, before recycling the product, the batteries must be removed and disposed of at a licensed collection point.

Disclaimer:

Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness.
No express or implied warranty or representation is given relating to the information contained in this document.
RF Solutions Ltd reserves the right to make changes and improvements to the product(s) described herein without notice.
Buyers and other users should determine for themselves the suitability of any such information or products for their particular requirements or specification(s).
RF Solutions Ltd shall not be liable for any loss or damage caused as a result of the user’s determination of how to deploy or use RF Solutions Ltd’s products.
Use of RF Solutions Ltd products or components in life support and/or safety applications is not authorized except with express written approval.
No licenses are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded.
This will not operate to limit or restrict RF Solutions Ltd’s liability for death or personal injury resulting from its negligence.